the because I'm bored build
#351
so then you would have to get a custom intermediate made. either way, its not going do be a bolt in and go without getting something made, rigging it up by spacing the axle at the hub, or getting lucky and finding an off the shelf axle from a different vehicle that works.
#353
Slobodan Milošević
iTrader: (8)
Looks like the part number for that shaft is 26034381. The carrier in the diagram looks like it wont work without modification
1994 Pontiac Grand AM Axle Shaft
INTERMED SHAFT | Genuine GM | 26034381
1994 Pontiac Grand AM Axle Shaft
INTERMED SHAFT | Genuine GM | 26034381
#363
#366
Former Vendor
iTrader: (4)
so then you would have to get a custom intermediate made. either way, its not going do be a bolt in and go without getting something made, rigging it up by spacing the axle at the hub, or getting lucky and finding an off the shelf axle from a different vehicle that works.
#369
well should get a good idea tomorrow what a stock f23 will hold.
taking phil's redline to slipstream racings spring invitational tomorrow. have nitrous jets up to a 250shot if we still can't get this thing to boost of 25.5psi (made 538whp boost only) shooting for 700whp for the race tomorrow. 1/2 mile dig racing.... oh hell yeah
my car will be out at the beast coast shootout this year finally. taking a few days off from work in a week to go through the car and fix the oil leaks and clean up some wiring. May throw the bottle in for that event.... we shall see
taking phil's redline to slipstream racings spring invitational tomorrow. have nitrous jets up to a 250shot if we still can't get this thing to boost of 25.5psi (made 538whp boost only) shooting for 700whp for the race tomorrow. 1/2 mile dig racing.... oh hell yeah
my car will be out at the beast coast shootout this year finally. taking a few days off from work in a week to go through the car and fix the oil leaks and clean up some wiring. May throw the bottle in for that event.... we shall see
#373
didn't get any vids yet, check out slipstream racing events on facebook for vids. only a few up so far, but I"m sure more will be up soon.
car held up pretty good. trans and axles stayed in one piece. unfortunately it was btwn 28-35 degrees out for the whole day, so nothing but wheel spin even in 4th gear on radials. phil's car did pretty good though, best trap of the day was 146.7mph (beat all the ferrari's out there lol).
I"ll have my car out at the beast coast shootout in july, and maybe at the pocono roll race event too. nitrous goes in this weekend along with the cut out and new plugs. let's see what she can do
car held up pretty good. trans and axles stayed in one piece. unfortunately it was btwn 28-35 degrees out for the whole day, so nothing but wheel spin even in 4th gear on radials. phil's car did pretty good though, best trap of the day was 146.7mph (beat all the ferrari's out there lol).
I"ll have my car out at the beast coast shootout in july, and maybe at the pocono roll race event too. nitrous goes in this weekend along with the cut out and new plugs. let's see what she can do
#374
looking forward to the nitrous install this weekend lol. gotta pick up new plugs though, may hold off spraying until I get the cut out installed as I have a feeling some of the spark issues are back pressure related. may just run open down pipe for some tests anyway lol.
#375
nitrous is up and running, spark issue is fixed. car is an animal.
registered for the beast coast shootout in july, but should be out at the track in a week or 2 to see what she can do.
need to hit the dyno again too. want to see 600whp on boost and 675+ on spray (only running an approx 55 shot right now)
registered for the beast coast shootout in july, but should be out at the track in a week or 2 to see what she can do.
need to hit the dyno again too. want to see 600whp on boost and 675+ on spray (only running an approx 55 shot right now)