Well i finally got my meth kit installed yesterday after i got my tb spacer from ott performance and the fittings i needed from ais. I also tinted my tails, i didnt wanna go too dark because VA cops can be dicks about little stuff like that... Let me know what yall think.











I dont know if i am gonna do the third brake light and side markers or not, u guys think i should leave it as is or tint those too?

 

Nice job man, everything looks clean, how much did you pay for you kit and did you retune afterwards? How much timing are you running now?

 

install look's good , nice placement on the Decal's , !!

 

Very nice looking.

 

I got the kit brand new from another member for 250 it was a sweet deal and i couldnt pass it up. I am taking it down to NC to Sunburst SS to get it tuned sometime this month or next month i gotta get my wideband in dual interceptors installed and i got a 2.85 on the way. I also gotta get my bung welded on for my wideband. Thanks for the comments guys.

 

so do you guys think i should tint the side markers and third brake light or what?

 

This "meth" injection. Is that like another way for "nitrous?" And does it really have to be a drug kind of word?? ROFL!

 

looks awesome, where did you run your line for your meth?

 

i drilled two little holes on the right side of the spare tire bay and used the supplied grommets and some sealant to keep the water out. I would have taken some pics but i have a bunch of **** in my trunk and it would have been a pain to lift it all out. Then i just routed it up the right side of the car and secured it with tie wraps and then up into the engine bay where the picture shows above.

 

I ran my meth lines into the engine bay through the same way you did. Keep a check on them. Mine started to melt and deform and eventually leak because of the heat of the header. I guess I'm going to run mine through the car and firewall now.

 

Yea i was just out lookin at mine and i dont really like the way they are...there is a couple of pinch points im worried about smashin em if i bottom out on a speed bump or somethin. Im gonna send denny a pm and ask him how he routed his through the inside.

 

Very nice, I love that color. I would leave the tinting as-is IMO

 

purdy red. almost got that color and would of had nicer seats

 

ah, well when you find out how he routed it through the car could you post it up here?

 

The 3rd brake light and side markers blend in pretty well i wouldnt bother, it would draw too much attention to them... IMO

 

yea i just got done reroutin mine i just went ahead and do it cuz i didnt hear back from denny. I just routed the tubing beside the brace for the back seat so it wouldnt get pinched, just pull the cushion over a little and u will see what im talkin about, then i just tucked it under the driver side panels and there is a huge rubber grommet that just pops out right behind the clutch and i just punched a hole in the engine bay side of the grommet with a flat head screwdriver then just pushed the tubing through. Then i jacked the car up and got my dad to grab the tubing while i fed it up from down below the car. It was kind of a PITA but now im not worried about it scrapin on somethin or snow and ice cracking it.

 

awesome, also why didnt you put the check valve right on the elbow bend? I think thats what I am going to be doing.

 

i thought about it but i figured it wouldnt hurt havin a couple inches of tubing in between them really no reason behind it...

 

alright cool, was the rest of the install fairly easy?

 

Yes, it looks stupid without them matching.

 

hell yea it was really easy the hard part was figurin out where to mount the tank

 

yah I got one of my friends to build me a bracket, it came out pretty good.

 

what kit did you get? The AIS kit is awesome it came with two brackets and everything is already hooked up just run the lines and supply power and a ground and it was good to go.

 

I got the devils own, I need to do everything lol.

 

Mind if I use this pic on the website?