so i bought a TB spacer from a member here and i have a devils own meth kit.

i took a look at the nozzle and it doesnt look like theres anyway it fits in there.

anyone know something i dont? it seems as though the threading gets smaller as it gets closer to the inside diameter of the ring. also there is no threading for an 1/8 inch on the iniside hole????

what the heck do i do????

thank you

 

it wont screw in at all?

 

it does from the outside in. but not the way it ought to. with the bolt part on the inside.

 

? what do you mean? can you post a pic of your nozzle pleae

 

this is what im talking about....

 

i said the nozzle not the tap itself.....

 

You need to get a different type of nozzel.

http://www.alcohol-injection.com/noz...31bebbd99dc36a

You need the outside mount type.

 

with the throttle body spacer you must use an outside mount designed nozzle, such as the devils own DO series. the the threads in there are 1/8" pipe thread. pipe threads taper, meaning they arent cut as deep the further in it goes.

 

ahhh ok well im mad now cuz i just took more pics lemme upload them for the hell of it....






thank you i will look into a different nozzle type. is this something i can maybe find at the hardware store?

 

just get a tap and run it all the way threw, finish making the threads... thats what i did. 1/8 NPT tap

 

Nope. Place your order now.

http://www.ottperformance.com/Meth-I...duct_info.html

Maybe they can get it shipped by tomorrow.

 

or buy a tap set and keep your nozzle spend less and have a new tool for the garage???? ehh? ehhh? new tool set?

 

ok, well now the question is what size nozzle? im basically between 5 or 7 gph.

insight?

thanks i is meth noob

 

That wont work with the thickness of his TB spacer. There would be no way to connect the nozzle to the check valve.

 

your right ebristol looking at the pics my nozzle is different i have a ais nozzle. good catch!

 

I am really not sold on Meth injection. I have a devil's own progressive meth kit and was running a 5gpm nozzle. I never got to finish tuning for it.

But my local performance shop told me that they did not see any hp gains with Meth injection unless the mixture was 75% meth or higher.

What I might try is running a 1gpm nozzle and only run water on low pressure. Just so I can get some of the cooling effects. But I have not made up my mind yet.

 

i have a ais as well. noob comment coming up... ais ftw!

 

I went through the same problem he did! lol With that same TB spacer too!

 

i run a 75/25 mix to a 80/20 mix

 

i use straight meth, pure M1

 

you cant run a tap through, if you did, nothing would ever seal and it would be a nightmare. order an outside mount nozzle and itll work great.

7gpm is too much. devils own has a calculator for nozzle size, with a 100psi pump (wich most are rated at 150 and over that with small nozzles) it calls for 3.8gph. taking the pump pressure into consideration, a 3gph should be about right.

i myself run a 2gph nozzle with 30% meth. every time i post anything more about my setup i get attacked, so ill refrain from giving more details.

 

i guess that can be argued

where do you get it or how do you make yours?

 

WTF!!! jk

Yeah its been a touchy subject around here for the last few months.

So far no one has dyno proven to make more hp with meth injection. I even think ZZP has a $1000 challenge out stating they can make more hp with out meth injection then anyone with meth injection on the same car.

So far no one has taken them up on the challenge.