So Cal Chat

[DSmastery]

hahaha true story

[Omnigear]

an anchor

[mofofernando]

mines rolled when not in gear before. my old driveway was steep though

[mrsilent13]

so i was thinking of going with a turbonetics turbo or master power turbo for my next setup...im going to be running 1mm oversized valves, 3 angle valve job, dual coil springs, ported and polished head. maybe ill use another garrett any of you have any suggestions?

[drew1991sf]

how much power u aiming for?

[mofofernando]

get the biggest turbo thatll fit haha

[HunterKiller89]

Originally Posted by mrsilent13

so i was thinking of going with a turbonetics turbo or master power turbo for my next setup...im going to be running 1mm oversized valves, 3 angle valve job, dual coil springs, ported and polished head. maybe ill use another garrett any of you have any suggestions?

borg-warner turbos usually outperform garrett turbos of the same size.

also:
http://www.allecotec.com/product_inf...985a2f48348b1f
http://www.allecotec.com/product_inf...985a2f48348b1f
.5mm over with fully built valvetrain for $1k. Then go get your head ported by M2Race for about another grand or so, and whala...probably the best flowing head on this site.

That was my planned build

[mofofernando]

turbo the GTO

[RooTBeeR]

Originally Posted by mrsilent13

lol....vtec...

hey andrew....my days off are tomorrow and tuesday...ill find out how much tires are for me...and ill try and get you a price....

alrighty, cool man. thanks

Originally Posted by mofofernando

turbo the GTO

nah, one is not enough... Twin Turbo it

[mofofernando]

nah, one is not enough... Twin Turbo it [/QUOTE]

even better

[HunterKiller89]

lol. ive already gone through the mods. Leaning towards a blower. Start with the magnuson kit (uses a M90 i believe?) and upgrade to a TVS 2300 down the road after I put one of these guys in:
http://www.jegs.com/p/Eagle/Eagle-LS...57303/10002/-1

hey, if im gonna forge the rotating assembly, and theyre all the same cost...why not up the cubes right?

[DSmastery]

notice anything different?

[Omnigear]

quad charge it 2 blowers and 2 turbos
you will need an oxygen mask because of
all the air it will suck out of the area.

[cobaltssoverbooster]

run a gt28r blowing into a gt4088r blowing into a gt60r and tell me how she pulls 8P

gt6041

[drew1991sf]

ls9 swap

[cobaltssoverbooster]

i saw the 6041 in action at pamona dragway running in the diesel dragsters and it pumps so much air it needs 2 60mm bov hahaha talk about a blowjob

[mrsilent13]

Originally Posted by HunterKiller89

borg-warner turbos usually outperform garrett turbos of the same size.

also:
http://www.allecotec.com/product_inf...985a2f48348b1f
http://www.allecotec.com/product_inf...985a2f48348b1f
.5mm over with fully built valvetrain for $1k. Then go get your head ported by M2Race for about another grand or so, and whala...probably the best flowing head on this site.

That was my planned build

thanks for the 1k price but the head is going to be done by SBR for $750 this will include the 1mm oversized valves, 3 way valve job, port and polish, and the dual coil valve springs and they will replace valve guides and seals as well for that same price...so ill be sending my head to them not this check but next check

[HunterKiller89]

Originally Posted by mrsilent13

thanks for the 1k price but the head is going to be done by SBR for $750 this will include the 1mm oversized valves, 3 way valve job, port and polish, and the dual coil valve springs and they will replace valve guides and seals as well for that same price...so ill be sending my head to them not this check but next check

damn. Thats a good deal right there too! lol