Cobalt SS Network

2.0L LSJ Performance Tech 205hp Supercharged SS tuner version. 200 lb-ft of torque.

Japeatr's knocking at the track rebuild thread

Thread Tools
 
Search this Thread
 
Old 06-05-2014, 01:31 AM
  #26  
Senior Member
iTrader: (1)
 
Spawne32's Avatar
 
Join Date: 11-24-08
Location: New Jersey
Posts: 2,675
Likes: 0
Received 1 Like on 1 Post
Originally Posted by lsjion
I think you had too much timing in it with the shot.
May consider pulling some next time around.
I'm sure IAT's weren't too friendly either
Doubt it, the rods arent damaged, nor does it appear it stuffed from any kind of detonation damage. Looks like he just exceeded the limits of the bearings briefly. Need to run clevite H bearings if you're going to push the limits that much.
Spawne32 is offline  
Reply Like
Old 06-05-2014, 07:02 AM
  #27  
South Central *********
Thread Starter
iTrader: (9)
 
JapEatr's Avatar
 
Join Date: 05-14-05
Location: Texas
Posts: 6,176
Received 48 Likes on 38 Posts
Oem
JapEatr is offline  
Reply Like
Old 06-05-2014, 07:06 AM
  #28  
Super Moderator
iTrader: (3)
 
mrbelvedere's Avatar
 
Join Date: 12-03-05
Location: KY
Posts: 8,165
Received 51 Likes on 45 Posts
Originally Posted by Spawne32
Doubt it, the rods arent damaged, nor does it appear it stuffed from any kind of detonation damage. Looks like he just exceeded the limits of the bearings briefly. Need to run clevite H bearings if you're going to push the limits that much.
he had way to much timing in the engine for spraying people have sprayed a lot more then him without damage because they pulled timing
mrbelvedere is offline  
Reply Like
Old 06-05-2014, 07:13 AM
  #29  
Administrator
Administrator
Platinum Member
iTrader: (25)
 
Staged07SS's Avatar
 
Join Date: 12-30-07
Location: NEPA
Posts: 14,331
Received 197 Likes on 175 Posts
subd
Staged07SS is offline  
Reply Like
Old 06-05-2014, 07:18 AM
  #30  
Former Vendor
iTrader: (4)
 
Josh@ottp's Avatar
 
Join Date: 01-26-07
Location: Michigan
Posts: 3,286
Received 15 Likes on 8 Posts
Originally Posted by JapEatr
Are Bates and GMPP the only options for cam gears?
I have 50 sets being machined up right now. They are 4-6 weeks out though.
Josh@ottp is offline  
Reply Like
Old 06-05-2014, 07:33 AM
  #31  
Senior Member
 
Tjolley's Avatar
 
Join Date: 02-01-11
Location: modesto
Posts: 2,814
Likes: 0
Received 1 Like on 1 Post
Josh r they gona be priced better than the gmp or bates??
Tjolley is offline  
Reply Like
Old 06-05-2014, 07:50 AM
  #32  
Senior Member
 
Tjolley's Avatar
 
Join Date: 02-01-11
Location: modesto
Posts: 2,814
Likes: 0
Received 1 Like on 1 Post
Wonder wat kinda boost u will see on a 2.0l with the 2.4 pulley.
I see 28-29 psi at 8000 rpm

Also u planning on some FIC 190# Injectors. If so let me know so I can help u with fitment they don't exactly drop in.
Tjolley is offline  
Reply Like
Old 06-05-2014, 09:25 AM
  #33  
Former Vendor
iTrader: (4)
 
Josh@ottp's Avatar
 
Join Date: 01-26-07
Location: Michigan
Posts: 3,286
Received 15 Likes on 8 Posts
They will be cheaper than gmpp by a lot.
Josh@ottp is offline  
Reply Like
Old 06-05-2014, 09:45 AM
  #34  
South Central *********
Thread Starter
iTrader: (9)
 
JapEatr's Avatar
 
Join Date: 05-14-05
Location: Texas
Posts: 6,176
Received 48 Likes on 38 Posts
Originally Posted by Spawne32
Doubt it, the rods arent damaged, nor does it appear it stuffed from any kind of detonation damage. Looks like he just exceeded the limits of the bearings briefly. Need to run clevite H bearings if you're going to push the limits that much.
Thats the plan
JapEatr is offline  
Reply Like
Old 06-05-2014, 10:24 AM
  #35  
Senior Member
 
alerosaint's Avatar
 
Join Date: 08-06-08
Location: Federal Way
Posts: 3,414
Received 7 Likes on 7 Posts
When you work out the kinks she gonna be pretty awesome Jap
alerosaint is offline  
Reply Like
Old 06-05-2014, 10:52 AM
  #36  
Senior Member
iTrader: (4)
 
Hockeyman's Avatar
 
Join Date: 08-10-07
Location: DFW
Posts: 5,636
Received 8 Likes on 8 Posts
gonna be a beast fah
Hockeyman is offline  
Reply Like
Old 06-05-2014, 12:07 PM
  #37  
South Central *********
Thread Starter
iTrader: (9)
 
JapEatr's Avatar
 
Join Date: 05-14-05
Location: Texas
Posts: 6,176
Received 48 Likes on 38 Posts
Originally Posted by Tjolley
Wonder wat kinda boost u will see on a 2.0l with the 2.4 pulley.
I see 28-29 psi at 8000 rpm

Also u planning on some FIC 190# Injectors. If so let me know so I can help u with fitment they don't exactly drop in.
thinking that is the route im going... will need tables for them tho
JapEatr is offline  
Reply Like
Old 06-05-2014, 12:19 PM
  #38  
Senior Member
iTrader: (1)
 
BlackielawlessSS's Avatar
 
Join Date: 10-03-13
Location: Haslet, TX
Posts: 18,486
Received 287 Likes on 265 Posts
Gl man
BlackielawlessSS is offline  
Reply Like
Old 06-05-2014, 12:26 PM
  #39  
Senior Member
iTrader: (4)
 
InfraRedline's Avatar
 
Join Date: 08-22-08
Location: Alpharetta, GA
Posts: 7,190
Likes: 0
Received 6 Likes on 5 Posts
Damn, sucks to hear that And you must have been having one hell of a time with 3rd with that trap speed! Should be at least another 10mph or so on spray.

Good attitude towards it though. Time to go stronger! Only 3,300 miles though, I have put that on mine this year already:/
InfraRedline is offline  
Reply Like
Old 06-05-2014, 12:30 PM
  #40  
South Central *********
Thread Starter
iTrader: (9)
 
JapEatr's Avatar
 
Join Date: 05-14-05
Location: Texas
Posts: 6,176
Received 48 Likes on 38 Posts
car is far from a daily or even a weekly driver, build race, tear apart, upgrade, etc. repeat
JapEatr is offline  
Reply Like
Old 06-05-2014, 12:31 PM
  #41  
Administrator
Administrator
Platinum Member
iTrader: (25)
 
Staged07SS's Avatar
 
Join Date: 12-30-07
Location: NEPA
Posts: 14,331
Received 197 Likes on 175 Posts
Can't wait until she is back together.

If you hit 394 whp with your old setup, I can only imagine what she will make now.
Staged07SS is offline  
Reply Like
Old 06-05-2014, 12:34 PM
  #42  
Senior Member
iTrader: (2)
 
jonathan923's Avatar
 
Join Date: 01-07-09
Location: Queens, NY
Posts: 7,881
Likes: 0
Received 1 Like on 1 Post
damm sucks to see this man. but glad your putting her on the street again with a nasty more aggressive setup. i was hoping to see 13.3 @ 120mph+ ridiculous trap lol
jonathan923 is offline  
Reply Like
Old 06-05-2014, 12:34 PM
  #43  
Got Bewst?
iTrader: (8)
 
Bluelightning's Avatar
 
Join Date: 03-16-10
Location: Winnipeg, Manitoba
Posts: 11,034
Received 33 Likes on 32 Posts
Did I miss something on that? Thought you made like 383whp the last dyno run.
Bluelightning is offline  
Reply Like
Old 06-05-2014, 12:39 PM
  #44  
Senior Member
iTrader: (4)
 
InfraRedline's Avatar
 
Join Date: 08-22-08
Location: Alpharetta, GA
Posts: 7,190
Likes: 0
Received 6 Likes on 5 Posts
Mine isn't intended to be the daily, but when its nice out I try to get all the driving in I can since we don't have the luxury of year round nice weather like you lucky bastards
InfraRedline is offline  
Reply Like
Old 06-05-2014, 12:40 PM
  #45  
Senior Member
iTrader: (1)
 
Spawne32's Avatar
 
Join Date: 11-24-08
Location: New Jersey
Posts: 2,675
Likes: 0
Received 1 Like on 1 Post
Originally Posted by JapEatr
Thats the plan
good man, I love the performance of clevite HX bearings. Always had fantastic success with them.
Spawne32 is offline  
Reply Like
Old 06-05-2014, 12:55 PM
  #46  
South Central *********
Thread Starter
iTrader: (9)
 
JapEatr's Avatar
 
Join Date: 05-14-05
Location: Texas
Posts: 6,176
Received 48 Likes on 38 Posts
Originally Posted by Bluelightning
Did I miss something on that? Thought you made like 383whp the last dyno run.
That 383 was on a 105* day. Same setup, better weather and more fuel... Better results

There never sent me the graph
JapEatr is offline  
Reply Like
Old 06-05-2014, 01:32 PM
  #47  
Senior Member
iTrader: (1)
 
Spawne32's Avatar
 
Join Date: 11-24-08
Location: New Jersey
Posts: 2,675
Likes: 0
Received 1 Like on 1 Post
I'd probably consider upgrading the rod bolts at this point in time as well if you havent already, just my suggestion.
Spawne32 is offline  
Reply Like
Old 06-05-2014, 01:35 PM
  #48  
Senior Member
iTrader: (4)
 
Hockeyman's Avatar
 
Join Date: 08-10-07
Location: DFW
Posts: 5,636
Received 8 Likes on 8 Posts
Got locked out in both 2nd and 3rd gear when I took it down the track. So much time lost.
Hockeyman is offline  
Reply Like
Old 06-05-2014, 01:44 PM
  #49  
South Central *********
Thread Starter
iTrader: (9)
 
JapEatr's Avatar
 
Join Date: 05-14-05
Location: Texas
Posts: 6,176
Received 48 Likes on 38 Posts
Originally Posted by Spawne32
I'd probably consider upgrading the rod bolts at this point in time as well if you havent already, just my suggestion.
I run ARP2000 rod bolts

It wasnt just driver mod, Hockeyman drove it too, he refused to spray tho lol
JapEatr is offline  
Reply Like
Old 06-05-2014, 01:54 PM
  #50  
Senior Member
iTrader: (4)
 
Hockeyman's Avatar
 
Join Date: 08-10-07
Location: DFW
Posts: 5,636
Received 8 Likes on 8 Posts
Woulda sprayed on 3rd run if it didn't start telling knock knock jokes.
Hockeyman is offline  
Reply Like



Advanced Search
Quick Reply: Japeatr's knocking at the track rebuild thread


Reply Closed Thread Share

All times are GMT -4. The time now is 08:56 PM.