Cobalt SS Network - Search Results



Showing results 1 to 20 of 33
Search took 0.00 seconds.
Search: Posts Made By: mrbelvedere
Forum: 2.0L LSJ Performance Tech 10-12-2017, 05:25 PM
Replies: 5
Views: 238
Posted By mrbelvedere
the shims are for the vvt engines the cam gears...

the shims are for the vvt engines the cam gears are a few thousands farther out then the non vvt engines so they space the lower cam gear out so the chain lines up
Forum: 2.0L LSJ Performance Tech 09-10-2017, 01:54 PM
Replies: 134
Views: 2,487
Posted By mrbelvedere
its quite clear you do not know how the pcv...

its quite clear you do not know how the pcv system works it just does not vent into the hose to the air intake

under normal driving vacuum from the intake manifold pulls air through the tube on...
Forum: 2.0L LSJ Performance Tech 07-07-2017, 02:21 AM
Replies: 28
Views: 964
Posted By mrbelvedere
omg do cooling mods before it melts there is more...

omg do cooling mods before it melts there is more then enough information on this site to answer any pulley question out there you just need to search and your first mod should be a wideband fueling...
Forum: 2.0L LSJ Performance Tech 07-03-2017, 12:43 PM
Replies: 134
Views: 2,487
Posted By mrbelvedere
I pointed out where your spending money you that...

I pointed out where your spending money you that there is need for so that way you can spend the money were it would better benefit the package



if you cooked a piston that quickly you or the...
Forum: 2.0L LSJ Performance Tech 06-29-2017, 05:38 PM
Replies: 134
Views: 2,487
Posted By mrbelvedere
why be cheap and use stock rods and you do not...

why be cheap and use stock rods and you do not need to reinvent the pcv system there are ways of making it better and a single disk clutch will hold more then what you need
Forum: Problems/Service/Maintenance 04-15-2017, 10:40 PM
Replies: 5
Views: 203
Posted By mrbelvedere
email zzp about the problem they will probably...

email zzp about the problem they will probably want the pcm back to reflash it
Forum: Problems/Service/Maintenance 04-12-2017, 10:06 AM
Replies: 13
Views: 400
Posted By mrbelvedere
if the noise goes away you may have damaged the...

if the noise goes away you may have damaged the blower
Forum: 2.0L LSJ Performance Tech 04-01-2017, 06:34 PM
Replies: 115
Views: 6,650
Posted By mrbelvedere
you are 100% clueless there is big difference...

you are 100% clueless there is big difference between a k series head and an ecotec head the amount of air they move is stupid compared to an ecotec head and then they have the best valve train setup...
Forum: 2.0L LSJ Performance Tech 03-16-2017, 01:41 PM
Replies: 115
Views: 6,650
Posted By mrbelvedere
bull shit all it did was set in a garage and that...

bull shit all it did was set in a garage and that is the worst way for a car to die
Forum: 2.0L LSJ Performance Tech 02-17-2017, 09:02 AM
Replies: 115
Views: 6,650
Posted By mrbelvedere
picked up over the hyd comps with less timing the...

picked up over the hyd comps with less timing the car is seeing 16 to [email protected] was at 22 to 23deg on the comp cams the iat2 was within 5deg of each other 175 to 180 on the dyno I am running a stock...
Forum: Problems/Service/Maintenance 01-16-2017, 05:35 PM
Replies: 5
Views: 403
Posted By mrbelvedere
call crate engine depot 1888 441 5150 ask for...

call crate engine depot 1888 441 5150 ask for tom he can help you
Forum: 2.0L LSJ Performance Tech 10-24-2016, 09:40 PM
Replies: 50
Views: 1,893
Posted By mrbelvedere
your messing up putting lnf piston and rods in

your messing up putting lnf piston and rods in
Forum: 2.0L LSJ Performance Tech 10-12-2016, 01:19 PM
Replies: 5
Views: 1,020
Posted By mrbelvedere
it might be the black wcc mesh behind the grilles...

it might be the black wcc mesh behind the grilles causing you problems
Forum: 2.0L LSJ Performance Tech 10-12-2016, 01:13 PM
Replies: 5
Views: 672
Posted By mrbelvedere
its a waste of time and to small to fool with put...

its a waste of time and to small to fool with put a 20g at a minimum on it but this has been done use the search button and go read
Forum: Problems/Service/Maintenance 09-25-2016, 01:30 PM
Replies: 3
Views: 385
Posted By mrbelvedere
p0017 is cam crank correlation and that will be...

p0017 is cam crank correlation and that will be thrown for an engine that is out of time and possibly a bad sensor a cam sensor housing out of time will not cause a p0017
Forum: 2.0L LSJ Performance Tech 09-10-2016, 08:46 PM
Replies: 156
Views: 12,898
Posted By mrbelvedere
comp cams are ok they will give you a generic...

comp cams are ok they will give you a generic grind for the ecotec and they did not put the hex in the cam correctly but there are better choices out there good luck
Forum: 2.0L LSJ Performance Tech 08-22-2016, 10:53 AM
Replies: 12
Views: 873
Posted By mrbelvedere
the inj were dam near maxed from the factory and...

the inj were dam near maxed from the factory and you will pick up hp from an inj change it gives you room to up the rpm and to run an aggressive timing map
Forum: 2.0L LNF Performance Tech 08-11-2016, 02:46 PM
Replies: 34
Views: 1,085
Posted By mrbelvedere
You can resurface the flywheel

You can resurface the flywheel
Forum: Problems/Service/Maintenance 07-15-2016, 01:33 AM
Replies: 8
Views: 477
Posted By mrbelvedere
its a dampener not a balancer and if you remove...

its a dampener not a balancer and if you remove it bad shit happens
Forum: 2.0L LSJ Performance Tech 04-28-2016, 10:09 AM
Replies: 24
Views: 1,035
Posted By mrbelvedere
he is referring to extending the keyway making it...

he is referring to extending the keyway making it longer if the stock key shears you loose the oil pump
Showing results 1 to 20 of 33

 
Forum Jump

All times are GMT -4. The time now is 11:50 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.