Cobalt SS Network - Search Results

 
Search: Posts Made By: mrbelvedere
Showing results 1 to 20 of 38
Search took 0.02 seconds.
05-10-2018, 01:39 PM
Replies: 12
Views: 807
Posted By mrbelvedere

raise the compression run a bigger pulley make mo...

raise the compression run a bigger pulley make mo power
05-10-2018, 09:43 AM
Replies: 24
Views: 2,264
Posted By mrbelvedere

go to facebook look up category 5 port work he...

go to facebook look up category 5 port work he specializes in ecotec heads
05-08-2018, 08:44 AM
Replies: 24
Views: 2,264
Posted By mrbelvedere

the stock pcv system is the best way to keep it...

the stock pcv system is the best way to keep it so it you pull a vacuum on the crank case on the external pcv line on the back of the valve cover remove it and weld a -10 fitting in place of the...
05-03-2018, 10:27 AM
Replies: 24
Views: 2,264
Posted By mrbelvedere

people can only guess at the power out put ...

people can only guess at the power out put

for 1 you need to run the lsj belt setup and tensioner the belt is a double sided 6 rib belt im sure you can get a power steering pulley made to fit
...
04-13-2018, 07:42 AM
Replies: 11
Views: 785
Posted By mrbelvedere

the pump is not that loud on thee cars

the pump is not that loud on thee cars
10-12-2017, 04:25 PM
Replies: 5
Views: 750
Posted By mrbelvedere

the shims are for the vvt engines the cam gears...

the shims are for the vvt engines the cam gears are a few thousands farther out then the non vvt engines so they space the lower cam gear out so the chain lines up
09-10-2017, 12:54 PM
Replies: 134
Views: 4,038
Posted By mrbelvedere

its quite clear you do not know how the pcv...

its quite clear you do not know how the pcv system works it just does not vent into the hose to the air intake

under normal driving vacuum from the intake manifold pulls air through the tube on...
07-07-2017, 01:21 AM
Replies: 28
Views: 2,310
Posted By mrbelvedere

omg do cooling mods before it melts there is more...

omg do cooling mods before it melts there is more then enough information on this site to answer any pulley question out there you just need to search and your first mod should be a wideband fueling...
07-03-2017, 11:43 AM
Replies: 134
Views: 4,038
Posted By mrbelvedere

I pointed out where your spending money you that...

I pointed out where your spending money you that there is need for so that way you can spend the money were it would better benefit the package



if you cooked a piston that quickly you or the...
06-29-2017, 04:38 PM
Replies: 134
Views: 4,038
Posted By mrbelvedere

why be cheap and use stock rods and you do not...

why be cheap and use stock rods and you do not need to reinvent the pcv system there are ways of making it better and a single disk clutch will hold more then what you need
04-15-2017, 09:40 PM
Replies: 5
Views: 304
Posted By mrbelvedere

email zzp about the problem they will probably...

email zzp about the problem they will probably want the pcm back to reflash it
04-12-2017, 09:06 AM
Replies: 13
Views: 501
Posted By mrbelvedere

if the noise goes away you may have damaged the...

if the noise goes away you may have damaged the blower
04-01-2017, 05:34 PM
Replies: 115
Views: 11,643
Posted By mrbelvedere

you are 100% clueless there is big difference...

you are 100% clueless there is big difference between a k series head and an ecotec head the amount of air they move is stupid compared to an ecotec head and then they have the best valve train setup...
03-16-2017, 12:41 PM
Replies: 115
Views: 11,643
Posted By mrbelvedere

bull shit all it did was set in a garage and that...

bull shit all it did was set in a garage and that is the worst way for a car to die
02-17-2017, 08:02 AM
Replies: 115
Views: 11,643
Posted By mrbelvedere

picked up over the hyd comps with less timing the...

picked up over the hyd comps with less timing the car is seeing 16 to [email protected] was at 22 to 23deg on the comp cams the iat2 was within 5deg of each other 175 to 180 on the dyno I am running a stock...
01-16-2017, 04:35 PM
Replies: 5
Views: 597
Posted By mrbelvedere

call crate engine depot 1888 441 5150 ask for...

call crate engine depot 1888 441 5150 ask for tom he can help you
10-24-2016, 08:40 PM
Replies: 50
Views: 2,658
Posted By mrbelvedere

your messing up putting lnf piston and rods in

your messing up putting lnf piston and rods in
10-12-2016, 12:19 PM
Replies: 5
Views: 2,025
Posted By mrbelvedere

it might be the black wcc mesh behind the grilles...

it might be the black wcc mesh behind the grilles causing you problems
10-12-2016, 12:13 PM
Replies: 5
Views: 1,107
Posted By mrbelvedere

its a waste of time and to small to fool with put...

its a waste of time and to small to fool with put a 20g at a minimum on it but this has been done use the search button and go read
09-25-2016, 12:30 PM
Replies: 3
Views: 623
Posted By mrbelvedere

p0017 is cam crank correlation and that will be...

p0017 is cam crank correlation and that will be thrown for an engine that is out of time and possibly a bad sensor a cam sensor housing out of time will not cause a p0017
Showing results 1 to 20 of 38
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.