Cobalt SS Network
Share Your Pictures with Our Community. Upload Now
Had to jack the car up some more to get it all the way out. The drilled bleeder setup was bone dry, happy that held up
Had to jack the car up some more to get it all the way out. The drilled bleeder setup was bone dry, happy that held up
0 2022/06/20 18:26:36
0 2022/06/20 11:04:12
0 2022/06/20 11:04:05
0 2022/06/20 09:16:08
0 2022/06/20 09:16:07
Got the doohickey welded on on, a stopper on yhe other side prevented me from simply drilling another hole. I hope this works. This is zaving me from pulling the .75 bore MC out, and putting a 7/8 one which might need another adapter plate. Now greased with some red n tacky, and assemble. Which takes three or 4 hands to do, espevially with the seat in
Got the doohickey welded on on, a stopper on yhe other side prevented me from simply drilling another hole. I hope this works. This is zaving me from pulling the .75 bore MC out, and putting a 7/8 one which might need another adapter plate. Now greased with some red n tacky, and assemble. Which takes three or 4 hands to do, espevially with the seat in
0 2022/06/19 12:03:06
Got the clutch pedal out, which is a little awkward. After measuring. I fohnd the Z32 has around 6.5:1 pedal ratio. I am correcting to 5:1
Got the clutch pedal out, which is a little awkward. After measuring. I fohnd the Z32 has around 6.5:1 pedal ratio. I am correcting to 5:1
0 2022/06/19 12:02:47
"kustom" bleeder added to the solstice slave, it is much easier to bleed so far, i am fairly confident it should engage at the bottom quarter. At least, which leads to the next post.
"kustom" bleeder added to the solstice slave, it is much easier to bleed so far, i am fairly confident it should engage at the bottom quarter. At least, which leads to the next post.
0 2022/06/19 12:02:19
I somewhat expected my old headers to be fucked so I got some long tubes and slapped those on today
I somewhat expected my old headers to be fucked so I got some long tubes and slapped those on today
0 2022/06/18 19:29:56
0 2022/06/18 19:29:51
0 2022/06/18 19:29:02
0 2022/06/18 19:28:57
Advertisement
Slave setup, drilled bleeder. Well see how it goes
Slave setup, drilled bleeder. Well see how it goes
0 2022/06/17 20:17:51
0 2022/06/16 04:52:16
0 2022/06/16 04:52:01
0 2022/06/16 04:51:46
0 2022/06/16 04:51:36
0 2022/06/16 04:51:24
0 2022/06/16 04:51:11
0 2022/06/16 04:50:59
Drilled and tapped to 1/8. Something to note: i didnt drill the full length of the diameter of the tap. It is maybe 1/8, 1/4, and whatever the drill size is for the 1/8 npt. It does have continuity, but i am not able to pressure test until my lines show up. I am fairly confident it will work, and if i have to buy another MC anyway maybe i can help the community out while i am at it.
Drilled and tapped to 1/8. Something to note: i didnt drill the full length of the diameter of the tap. It is maybe 1/8, 1/4, and whatever the drill size is for the 1/8 npt. It does have continuity, but i am not able to pressure test until my lines show up. I am fairly confident it will work, and if i have to buy another MC anyway maybe i can help the community out while i am at it.
0 2022/06/15 13:43:39
0 2022/06/13 12:57:00
Unknown wire
Unknown wire
0 2022/06/13 12:30:26
Ground wire in wrong place
Ground wire in wrong place
0 2022/06/13 12:30:13
2 coats of clear. Super nice
2 coats of clear. Super nice
0 2022/06/13 09:24:43
2 coats of clear
2 coats of clear
0 2022/06/13 09:24:36
Finished sanding
Finished sanding
0 2022/06/13 09:24:28
The passenger side was just as bad, the angle doesn't make it look like it
The passenger side was just as bad, the angle doesn't make it look like it
0 2022/06/13 09:24:20
They were bad.
They were bad.
0 2022/06/13 09:24:10
I forgot to take pictures of doing the front, but it's basically the same as the back, except with some wet sanding on the primer to smooth it out before applying the colour shift paint
I forgot to take pictures of doing the front, but it's basically the same as the back, except with some wet sanding on the primer to smooth it out before applying the colour shift paint
0 2022/06/13 09:20:13
0 2022/06/13 09:20:03
0 2022/06/13 09:19:52
Advertisement