2.2L L61 Performance Tech 16 valve 145 hp EcoTec with 155 lb-ft of torque

video of my supercharged 2.2 at the track

Thread Tools
 
Search this Thread
 
Old May 29, 2009 | 10:37 AM
  #1  
misfitcobalt's Avatar
Thread Starter
New Member
 
Joined: 09-27-07
Posts: 114
Likes: 0
From: new york
video of my supercharged 2.2 at the track

http://www.youtube.com/watch?v=DWc9DeAQ-Fs
Reply
Old May 29, 2009 | 12:08 PM
  #2  
randizzle's Avatar
Senior Member
 
Joined: 05-04-07
Posts: 1,668
Likes: 0
From: MN
nice time!
Reply
Old May 29, 2009 | 12:14 PM
  #3  
Misery5567's Avatar
Senior Member
 
Joined: 05-19-07
Posts: 625
Likes: 0
From: Cheraw, SC
Very good.

I think best I've done in the 1/8 is a 9 flat spinning beam to beam

Good job!
Reply
Old May 29, 2009 | 01:35 PM
  #4  
IonNinja's Avatar
Senior Member
 
Joined: 07-29-05
Posts: 7,915
Likes: 0
From: AZ
What the hell was wrong with that Honda? Looked like one of my launches at the track.
Reply
Old May 29, 2009 | 01:41 PM
  #5  
Listerman's Avatar
Senior Member
 
Joined: 05-13-06
Posts: 752
Likes: 0
From: Cincy
what wheels are those? look like slipstreams
Reply
Old May 30, 2009 | 07:34 PM
  #6  
BlackCobalt707's Avatar
Senior Member
iTrader: (5)
 
Joined: 02-16-08
Posts: 8,405
Likes: 0
From: Fairfield, CA/Travis AFB, CA
lol poor honda...shoulda went B16 turbo
Reply
Old May 30, 2009 | 08:32 PM
  #7  
Sw4y1313's Avatar
Senior Member
 
Joined: 09-25-06
Posts: 1,860
Likes: 0
From: USAG Stuttgart, GER
Originally Posted by BlackCobalt707
lol poor honda...shoulda went B16 turbo
B16 turbo is a waste of money. Either stick with a D16 or go B18 or B20. You still have **** for torque with a B16.

But anyways, nice times!
Reply
Old May 30, 2009 | 10:06 PM
  #8  
tru2nrtt777's Avatar
Senior Member
iTrader: (1)
 
Joined: 02-08-08
Posts: 3,726
Likes: 0
From: Fayetteville/Linden, NC/Myrtle Beach, SC
Honda didnt look like he could hook up.
Reply
Old May 30, 2009 | 11:28 PM
  #9  
blackbolt89's Avatar
Senior Member
 
Joined: 10-28-08
Posts: 5,068
Likes: 0
From: New Milford, NJ
more like honda=fail.

that honda probably only had rice exterior and prob just a fart can.

i've found that around me almost all the hondas are riced on the outside and stock on the inside. it's a shame. cause some of those hondas could potentially be decent cars, if they actually had power. which they don't. lol
Reply
Old May 31, 2009 | 12:01 AM
  #10  
b_faulk75's Avatar
Senior Member
 
Joined: 12-21-06
Posts: 1,618
Likes: 0
From: WV
Wow!!! I bet this vid makes the honda community proud, lol.... Good track time!
Reply
Old May 31, 2009 | 12:04 AM
  #11  
mmcgee123's Avatar
Senior Member
iTrader: (1)
 
Joined: 07-22-08
Posts: 1,316
Likes: 0
From: troy,michigan
were u on dr's cus i run 13.6's at105-107 running 9.1 1/8ths
Reply
Old May 31, 2009 | 11:45 AM
  #12  
randizzle's Avatar
Senior Member
 
Joined: 05-04-07
Posts: 1,668
Likes: 0
From: MN
Originally Posted by blackbolt89
more like honda=fail.

that honda probably only had rice exterior and prob just a fart can.

i've found that around me almost all the hondas are riced on the outside and stock on the inside. it's a shame. cause some of those hondas could potentially be decent cars, if they actually had power. which they don't. lol
so a stock honda runs 9.49 with a shitty launch? i think not. what does your car run in the 1/8? i guarantee it's slower that 9.49.
Reply
Old May 31, 2009 | 07:58 PM
  #13  
misfitcobalt's Avatar
Thread Starter
New Member
 
Joined: 09-27-07
Posts: 114
Likes: 0
From: new york
my cobalt was running full slicks M&H i got down to a 8.98 this week running 13pounds....the honda isn't stock either it's my buddys car it is a built ls/vtec running 10 pounds but he has a probblem with his tune right now
Reply
Old Jun 1, 2009 | 10:53 PM
  #14  
jnicks510's Avatar
New Member
 
Joined: 05-18-09
Posts: 190
Likes: 0
From: Virginia
very nice time
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
brandon04
Problems/Service/Maintenance
46
Oct 21, 2015 07:04 AM
Tupp
Suspension
5
Sep 30, 2015 08:18 PM
Dylan Johnson
Suspension
9
Sep 30, 2015 08:57 AM
Extremespeed
South Pacific
0
Sep 29, 2015 04:34 AM




All times are GMT -4. The time now is 09:48 AM.