Ok guys, we have had a lot of interest in the Vibrant header package for the Cobalt SS recently.

So, we decided to dyno test the part, and show you guys the power it makes.

Heres the details.

First, the factory header and downpipe.
http://www.modernperformance.com/gm/dyno/cobaltfactoryheader.jpg

This is actually not a bad design for a factory piece, but theres several problem areas. First, look at the bung for the oxygen sensor. That part of the piping goes from nearly 2.75 inches all the way down to about 2 inches. Also, some other parts of the piping is as large as 3 inches, but then necks down to 2 inches in some areas. Lastly, in the collector for the header, where the four primaries merge into one, it is a whopping 1.6 inches in diameter!

http://www.modernperformance.com/gm/dyno/cobaltfactoryheader2.jpg

ENTER the Vibrant 4 into 1 Stainless steel header!

This piece is beautifully constructed of polished stainless steel, and has nice smooth bends, a nice smooth collector that merges the gases from the 4 cylinders into one, and a high flow catalytic convertor downpipe unit.

http://www.modernperformance.com/gm/cobalt_header_vibrant3.jpg

http://www.modernperformance.com/gm/cobalt_header_vibrant4.jpg

Dyno results :
Our 05 project Cobalt SS car already had a K&N air intake, and Vibrant exhaust, and a 3.1 inch pulley to increase the boost.

We installed the header, and noticed a very good gain in power. Peak hp gained was 8 hp and 3 lbs of torque, but throughout dyno, there were gains of 7-12 hp and torque. The blue line is the HP and torque after the header was installed, the red is the power before.

http://www.modernperformance.com/gm/dyno/cobaltvibranthdrdyno.jpg

We're very pleased with this header from Vibrant. Overall, with adding the 3.1 pulley, and the header, our cars power went from 219 hp and 180 torque to 240 hp and 202 torque at the wheels.

For more details on this header, and additional photos, check out modernperformance.com

To order, just call us toll free at 1-877-247-6366. We keep these IN stock, and can get one to you within a few days by Fedex !

Price and support for just LSJ?

Price and support for just LSJ?

Price for the Header and downpipe with high flow catalytic convertor is $609.99.

This particular header will only work with the Cobalt SS, HOWEVER we have a header that is exactly the same (From Vibrant) except for a few minor changes that is designed for the Ion Redline. Its priced at $609 as well.

We have no doubt youd make the exact same power levels, maybe even more with this header installed on your Ion Redline.

Nice--I've been waiting for someone to do a dyno before I plinked down that kind of cash for the Vibrant setup (although I already wanted it pretty badly) :)

NOICE numbers, and a damn nice product. This may be the header that I go with.

damn, nice to see some one backing the claim up with real numbers, thats a pretty header

NOICE numbers, and a damn nice product. This may be the header that I go with.

Its a great piece, and we have had a business relationship with Vibrant now for close to 8 years, and they have always put out top notch quality products, and they have stood behind them!

I really like the fact that this piece has a race catalytic convertor on it. That way, you can get the most power available, while still being legal. I have Vibrants race catalytic convertors on several of my cars, including my 95 Dodge Neon 2.4 swapped car and they work great for me.

Does anyone know how these two combined together sound on a cobalt ss/sc...with either a magnaflow muffler or any of the other mufflers available..im intressted in the kit,but dont want to buy it if my car would sound like a honda with a whine

Awesome to hear. I have their cat-back and LOVE the sound of it. How much do you think I will lose on the bottom end by adding their header and DP?? Any idea on how the sound may change?

Bump for some input

is there a catless option for this set up?

Does anyone know how these two combined together sound on a cobalt ss/sc...with either a magnaflow muffler or any of the other mufflers available..im intressted in the kit,but dont want to buy it if my car would sound like a honda with a whine

If you have the Magnaflow, along with this header it will be louder.

The problem is, that most exhausts that are 3 inch, dont absorb much of the sound frequencies. Thats why most 3 inch exhausts are louder than stock, and are even a tad bit raspy.

If you dont like the sound of your car, before or after installing any exhaust components, we have a whole line of inline mufflers, and resonators available. You could easily take your car to a muffler shop, and have them weld in either one (resonator reduces sound by about 5-8%, inline muffler 18-25%) for less than $20 or so, and resonators cost $40, muffler $65.

Awesome to hear. I have their cat-back and LOVE the sound of it. How much do you think I will lose on the bottom end by adding their header and DP?? Any idea on how the sound may change?

Bump for some input

You will not lose any torque at any point across the rpm band.

It might be hard to see since the image of the dyno is small, but look at the lowest point on the dyno, at 3100 rpms, there is a gain of over 10 ft lbs of torque before and after !!

Sound will increase by probably a good 10-15%.

you guys should test the weapon R 4-2-1 as well before i make a decisison

well im on 2.5" piping with only a magnaflow muffler..didnt really see a point in buying a catback for 300+bux when i can make my own for about 150...same design just not stainless steal

is there a catless option for this set up?

No there isnt.
Frankly, the car would be obnoxiously loud without a cat. For the 3-4 hp difference youd make without a catalytic convertor, over this high flow catalytic convertor, I would NOT do it.

Plus, in most states, not having a catalytic convertor will make it impossible to pass emissions testing, so for just about all our customers it wouldnt be worth it.

well im on 2.5" piping with only a magnaflow muffler..didnt really see a point in buying a catback for 300+bux when i can make my own for about 150...same design just not stainless steal

With you being in Chicago, youll notice within a year that your exhaust is severely rusting/falling apart if its not stainless. Hopefully at least you have aluminized steel at minimum.

Thank you for the input Cory. As soon as I get some extra funding, this will most likely be the direction that I go.

does the vibrant setup have a bung for wideband?

does the vibrant setup have a bung for wideband?

No it doesnt.
HOWEVER, for $25, we can take a stainless steel bung, and have it welded onto the header for you and ship it off to you. That would make installation easier for you.

Just call in your order, be sure to mention that you were told you could have an additional bung put in for $25 and we will take care of it.