New Video: HIDs
Original Hayden Fanatic
Platinum Member
Joined: 05-06-06
Posts: 33,169
Likes: 1
From: Dayton, O HI O
its n00bs like you that **** me off!!
Would it have been that difficult to say "that thread didnt answer my question, can someone give me a better answer?"
instead you chose to be a dick about it, which isnt
, 
and you made me have to go and give you -rep too 
i hope you learned a lesson here, otherwise your additude is going to be a problem, and make other members
, then youll go 
.now im done
this thread, have a 
and hope you enjoy the site 
.have a nice day
...sorry if there are to many
for you. 
Senior Member
Joined: 05-20-06
Posts: 5,450
Likes: 0
From: Jacksonville, Florida
dont be a dick!!
its n00bs like you that **** me off!!
Would it have been that difficult to say "that thread didnt answer my question, can someone give me a better answer?"
instead you chose to be a dick about it, which isnt, and you made me have to go and give you -rep too
i hope you learned a lesson here, otherwise your additude is going to be a problem, and make other members, then youll go .
now im done this thread, have a and hope you enjoy the site .
have a nice day
...sorry if there are to many for you.
its n00bs like you that **** me off!!
Would it have been that difficult to say "that thread didnt answer my question, can someone give me a better answer?"
instead you chose to be a dick about it, which isnt
, and you made me have to go and give you -rep too i hope you learned a lesson here, otherwise your additude is going to be a problem, and make other members
, then youll go .now im done
this thread, have a and hope you enjoy the site .have a nice day
...sorry if there are to many
for you. Haha good **** man, I think this guy had some sand in his vagina anyways
Last edited by Rangerondubz; Aug 2, 2007 at 08:58 AM. Reason: Automerged Doublepost
Senior Member
Joined: 06-29-06
Posts: 1,425
Likes: 0
From: O'Fallon, Missouri
Thread Starter
Senior Member
Joined: 02-03-07
Posts: 2,553
Likes: 0
From: Missouri
Last edited by JKennedy1612; Aug 2, 2007 at 07:41 PM. Reason: Automerged Doublepost
Thread Starter
Senior Member
Joined: 02-03-07
Posts: 2,553
Likes: 0
From: Missouri
A couple of you guys have asked how to install the kit. This is a guide that shows you (backwards) what your setup should look like.
First tape underneath the headlight housing with masking tape so you don't scratch the car when taking it out. Remove the two bolts holding the headlight (10mm).
Remove the four tabs. This will give you some extra room to take out the headlight.
The extra space
Removing the headlight...
HID wires
What your headlight housing should look like with the kit installed and the HID bulb in.
Notice I cut the other option off the headlight for direct plug and play. Here is what the pieces look like that I cut off.
Bolts removed so far.
Here's what it looks like without the headlight.
These three cords here (turn signal, signal connector(blue), and HID connectors) need to be accessible. They hook into the headlight. (See above)
The headlight mount removed. 4 10mm bolts.
Where I mounted the fog ballast.
Where I mounted the headlight ballast. Yes there is a bolt drilled in to secure it.
First tape underneath the headlight housing with masking tape so you don't scratch the car when taking it out. Remove the two bolts holding the headlight (10mm).
Remove the four tabs. This will give you some extra room to take out the headlight.
The extra space
Removing the headlight...
HID wires
What your headlight housing should look like with the kit installed and the HID bulb in.
Notice I cut the other option off the headlight for direct plug and play. Here is what the pieces look like that I cut off.
Bolts removed so far.
Here's what it looks like without the headlight.
These three cords here (turn signal, signal connector(blue), and HID connectors) need to be accessible. They hook into the headlight. (See above)
The headlight mount removed. 4 10mm bolts.
Where I mounted the fog ballast.
Where I mounted the headlight ballast. Yes there is a bolt drilled in to secure it.
Thread Starter
Senior Member
Joined: 02-03-07
Posts: 2,553
Likes: 0
From: Missouri
NOTE: THIS IS THE FOG LIGHT RELAY
Ok now here's where most of you guys get confused. What I'm holding here is the ground/relay, follow the wire and you can see where its grounded.
What I'm holding here is the connector that goes into your HID ballast that runs from the relay.
Here I am holding the factory connector that goes into the connector coming from the relay.
Lastly, here I'm indicating which wire is not being used.
Ok now here's where most of you guys get confused. What I'm holding here is the ground/relay, follow the wire and you can see where its grounded.
What I'm holding here is the connector that goes into your HID ballast that runs from the relay.
Here I am holding the factory connector that goes into the connector coming from the relay.
Lastly, here I'm indicating which wire is not being used.
Thread Starter
Senior Member
Joined: 02-03-07
Posts: 2,553
Likes: 0
From: Missouri
Original Hayden Fanatic
Platinum Member
Joined: 05-06-06
Posts: 33,169
Likes: 1
From: Dayton, O HI O
how is he supposed to shut his mouth & talk to you at the same time :confussed:
damn, you must have ESP or something... You certainly are starting off on the right foot arn't you
nice "mini-"howto... im deff going to order some from that guy soon
nice "mini-"howto... im deff going to order some from that guy soon
Thread Starter
Senior Member
Joined: 02-03-07
Posts: 2,553
Likes: 0
From: Missouri
Original Hayden Fanatic
Platinum Member
Joined: 05-06-06
Posts: 33,169
Likes: 1
From: Dayton, O HI O
Original Hayden Fanatic
Platinum Member
Joined: 05-06-06
Posts: 33,169
Likes: 1
From: Dayton, O HI O
