How much does it usally cost to dyno?
10-07-2007, 08:03 PM
#1
Senior Member
Thread Starter
How much does it usally cost to dyno?
ok i want to see how much im making and to get a better tune and i was just wondering on how much it would cost? i found this place http://dreamchaserracing.com/AutoDyn%20Prices.pdf but i cant figure out the prices someone help? o and i have a gm stage 2 kit a CAI and 2.8 pully and a 2.5 catback
10-07-2007, 08:07 PM
#3
Senior Member
Thread Starter
10-08-2007, 07:47 AM
#10
Senior Member
Join Date: 11-04-05
Location: San Diego, CA
Posts: 1,056
Likes: 0
Received 0 Likes
on
0 Posts
the place i went to was 75$ for 3 runs or 100$ for an hour session. though i kinda got the hook up and did about 2 hrs with tuning advice, while my friend made the changes with hp tuners. only 150$
10-08-2007, 02:52 PM
#13
Senior Member
Join Date: 05-27-07
Location: USA
Posts: 1,547
Likes: 0
Received 0 Likes
on
0 Posts
Bad thing is, he charges $250 for the min. 1 hr. of dyno time.
About 30 min. away is a facility that uses a Dynapack (wheel hub) type dyno that only charges $100 for the min. 1 hr. on the dyno.
But I prefer the roller type dyno, so until I'm ready to install the Factory Warranteed St.1 or St.2 I don't see a reason to baseline my car just yet.
10-08-2007, 05:56 PM
#15
Senior Member
Join Date: 05-27-07
Location: USA
Posts: 1,547
Likes: 0
Received 0 Likes
on
0 Posts
10-09-2007, 05:33 AM
#17
Member
Join Date: 05-07-07
Location: Norcal east bay area
Posts: 380
Likes: 0
Received 0 Likes
on
0 Posts
Local guy here on the 1st Friday night of every month does 2 pulls for $25 with a/f. He used to do 3 pulls but with 40+ people showing up it was taking too long. No one needs 3 pulls anyway to see a numbers. 1 run will get the numbers unless the operator is a clutz.
Otherwise they are usually 3 pulls for $85- $125 regular prices between to local places.
Otherwise they are usually 3 pulls for $85- $125 regular prices between to local places.
10-09-2007, 01:25 PM
#22
Senior Member
Join Date: 11-23-06
Location: Texas boy stuck in an Iowa Cornfield
Posts: 2,855
Received 0 Likes
on
0 Posts
Don't know if SSCARTUNING is still tuning Cobalts but try PMin' him. He has expierence with HPtuners and Cobalts.
I'd ask Japeater also his car was tuned by him.
These guys are located down in the North Dallas area though may be a little to far to travel from stratford. Just another option.
I'd ask Japeater also his car was tuned by him.
These guys are located down in the North Dallas area though may be a little to far to travel from stratford. Just another option.
12-23-2007, 12:26 PM
#24
Senior Member
iTrader: (3)
Join Date: 10-23-07
Location: Central CT
Posts: 1,337
Likes: 0
Received 0 Likes
on
0 Posts
I'm in CT...the shop in Manchester is asking $600 for dyno tune with HPTuners...thought that was a little steep but the guys said it'll be perfect after that...so...I've also heard XXTuning is kinda expensive as well...
12-23-2007, 12:44 PM
#25
Senior Member
Join Date: 07-08-05
Location: Niceville, FL
Posts: 6,200
Likes: 0
Received 0 Likes
on
0 Posts
The Show Zone in Charleston xskier and I go to is as follows on pricing the last I knew:
$75 for three pulls
$100 for an hour self tuning 2WD
$125 for an hour self tuning 4WD/AWD
$150 for an hour professional tuning 2WD
$175 for an hour professional tuning 4WD/AWD
Most of the time if you do a street tune first, it'll only take an hour or two to fine tune it all in. If your starting from scratch for a new untested project like my twinscrew and have any issues at all, you're easily looking at 4+ hours! That bill was over $600 for me, but luckily Colin taught me how to use HPTuners correctly during that time so I can do a lot of stuff myself now. Good Luck either way.
$75 for three pulls
$100 for an hour self tuning 2WD
$125 for an hour self tuning 4WD/AWD
$150 for an hour professional tuning 2WD
$175 for an hour professional tuning 4WD/AWD
Most of the time if you do a street tune first, it'll only take an hour or two to fine tune it all in. If your starting from scratch for a new untested project like my twinscrew and have any issues at all, you're easily looking at 4+ hours! That bill was over $600 for me, but luckily Colin taught me how to use HPTuners correctly during that time so I can do a lot of stuff myself now. Good Luck either way.