Mark this thread as Unsold
For Sale Aftermarket Sale, Take a Look
#1
New Member
Thread Starter
Join Date: 06-02-13
Location: gulf breeze
Posts: 134
Likes: 0
Received 0 Likes
on
0 Posts
Aftermarket Sale, Take a Look
I have some stuff that needs to be sold unfortunately.
I have a briefly used OBX log T3 manifold that has a fabricated piece of 304 pipe and wastegate flange welded on it. I stress cut the flange, and clocked the wastegate pipe at 135(give or take)degrees. It also has Arp bolts and washers. I'm not sure if any of you guys could use it, but if so it is for sale. 125$ + ship
I have an Aem TruBoost (never used), just an old package. the solenoid has some scuffs on it. Anyways $200+ship
Turbonetics Raptor BOV(along with 2 pieces of pipe and flange) - was used on test fit up and engine idle, valve still good. $150 OBO +shipping
I have a briefly used Cyborg Borg Warner T3/4 Turbocharger with ported housings(very nice). The CHRA is in good condition and the shaft play is like it was new. This is basically a new turbocharger. It was also used on a test build. Has drain fitting and restrictor feed. I will have to get back with you on turbo trim but if I am guessing right I have a exhaust wheel = 68 trim, and compressor wheel = 53 trim. Ill get back on this maybe tonight, it could be wrong. It is a very nice turbo with a 2.5 vband on the exhaust housing. The compressor housing was tapped into for positive vac source in 2 locations. There are a couple of options to go about this or leave it be. I believe I bought this on eBay for almost $700 ( I still have the receipt). This turbo was made by ExclusiveTurbosystems or chargers. I am asking $460 + ship. I think they sell the new cyborg's for 900$ on their website.
Have a bundle of an fittings as well plus a cbm adapter fuel rail - $40 freeship?
I also have a new intercooler( will get dimensions tonight or tomorrow), maybe a box of 2.5" intercooler pipe. I might have some more stuff back in florida that I cannot remember either.
I have more pictures of everything if need be, Also I am living in Galveston TX for time being and can travel if close by-Houston, TX...etc
I have a briefly used OBX log T3 manifold that has a fabricated piece of 304 pipe and wastegate flange welded on it. I stress cut the flange, and clocked the wastegate pipe at 135(give or take)degrees. It also has Arp bolts and washers. I'm not sure if any of you guys could use it, but if so it is for sale. 125$ + ship
I have an Aem TruBoost (never used), just an old package. the solenoid has some scuffs on it. Anyways $200+ship
Turbonetics Raptor BOV(along with 2 pieces of pipe and flange) - was used on test fit up and engine idle, valve still good. $150 OBO +shipping
I have a briefly used Cyborg Borg Warner T3/4 Turbocharger with ported housings(very nice). The CHRA is in good condition and the shaft play is like it was new. This is basically a new turbocharger. It was also used on a test build. Has drain fitting and restrictor feed. I will have to get back with you on turbo trim but if I am guessing right I have a exhaust wheel = 68 trim, and compressor wheel = 53 trim. Ill get back on this maybe tonight, it could be wrong. It is a very nice turbo with a 2.5 vband on the exhaust housing. The compressor housing was tapped into for positive vac source in 2 locations. There are a couple of options to go about this or leave it be. I believe I bought this on eBay for almost $700 ( I still have the receipt). This turbo was made by ExclusiveTurbosystems or chargers. I am asking $460 + ship. I think they sell the new cyborg's for 900$ on their website.
Have a bundle of an fittings as well plus a cbm adapter fuel rail - $40 freeship?
I also have a new intercooler( will get dimensions tonight or tomorrow), maybe a box of 2.5" intercooler pipe. I might have some more stuff back in florida that I cannot remember either.
I have more pictures of everything if need be, Also I am living in Galveston TX for time being and can travel if close by-Houston, TX...etc
#2
New Member
Thread Starter
Join Date: 06-02-13
Location: gulf breeze
Posts: 134
Likes: 0
Received 0 Likes
on
0 Posts
Man this prob too hard to sell on here.
Anyways most of the information I have on this listing is correct.
The turbonetics raptor bov is a 38mm greddy-type bov setup.
The intercooler I have is a 2.5' inlet/outlet. Specs: 28x9x2.75
The AN fittings I have in the pic, overall a hell of a buy, With what is there I would take a guess it could be close to 100 or more$. Some of those fittings are about 15$ a piece. Xcel 6AN swivel are 44$ for just 2 of them, Russel 4an straight (2) $20. Just an idea. They are expensive. Hell of a bargain for whoever wants it.
Anyways most of the information I have on this listing is correct.
The turbonetics raptor bov is a 38mm greddy-type bov setup.
The intercooler I have is a 2.5' inlet/outlet. Specs: 28x9x2.75
The AN fittings I have in the pic, overall a hell of a buy, With what is there I would take a guess it could be close to 100 or more$. Some of those fittings are about 15$ a piece. Xcel 6AN swivel are 44$ for just 2 of them, Russel 4an straight (2) $20. Just an idea. They are expensive. Hell of a bargain for whoever wants it.
#7
New Member
Thread Starter
Join Date: 06-02-13
Location: gulf breeze
Posts: 134
Likes: 0
Received 0 Likes
on
0 Posts
I put this stuff in storage on Friday. I'll be back over to box some of it to carry it in car. Hopefully this weekend if I am not working.
I'll double check the wastegate valve too
I'll double check the wastegate valve too
#9
New Member
Thread Starter
Join Date: 06-02-13
Location: gulf breeze
Posts: 134
Likes: 0
Received 0 Likes
on
0 Posts
Its an off brand intercooler like cx racing. no longer is it up for shipment as a buddy of mine has it. He will decide what to do with it...
Also for sale is a L61 Lightly CNC ported intake/exhaust & fully machined head. ready for fresh assembly as well as more machine work. over 300$ invested in this BARE head. Comes with camshaft caps, has all valve guides, and of course valve seats have been reground to their angles.
160$ located near Houston.
Also for sale is a L61 Lightly CNC ported intake/exhaust & fully machined head. ready for fresh assembly as well as more machine work. over 300$ invested in this BARE head. Comes with camshaft caps, has all valve guides, and of course valve seats have been reground to their angles.
160$ located near Houston.
Thread
Thread Starter
Forum
Replies
Last Post