Mark this thread as Unsold
For Sale moving out clean up sale. !!!!!
#1
Name : Luis
Location 07060
Contact: pm or send a text 908-8O9-O0˛⁴
Cleaning up and posting stuff as it becomes reachable.
All + shipping and PayPal fees.
Block off plate. 10$ - sold
IRL freshly powdercoated. Lots of knuckle skin and sweat was put into these to make them clean and fresh.
550$
Ss/TC springs. Have close to 600 miles. Been in storage since forever.
100$
misc lnf stuff. Cams -50.
Rad brackets - 25
Hpfp - free - sold
Bolts - 1-10$
dp gasket - sold
Intake manifold gasket - sold
More stuff from engine.
Pistons - 20$ each. Perfect for a project lamp
Cover - sold
Stock shifter - 25. No shift pattern
Hursts needs repair comes with housing - 80$
Let's try to keep it in the lower 48 states but if its small and ur Canadian. Don't be afraid to ask for shipping.
More stuff will become available as I keep cleaning. Have to get rid of this stuff before I move.
Location 07060
Contact: pm or send a text 908-8O9-O0˛⁴
Cleaning up and posting stuff as it becomes reachable.
All + shipping and PayPal fees.
Block off plate. 10$ - sold
IRL freshly powdercoated. Lots of knuckle skin and sweat was put into these to make them clean and fresh.
550$
Ss/TC springs. Have close to 600 miles. Been in storage since forever.
100$
misc lnf stuff. Cams -50.
Rad brackets - 25
Hpfp - free - sold
Bolts - 1-10$
dp gasket - sold
Intake manifold gasket - sold
More stuff from engine.
Pistons - 20$ each. Perfect for a project lamp
Cover - sold
Stock shifter - 25. No shift pattern
Hursts needs repair comes with housing - 80$
Let's try to keep it in the lower 48 states but if its small and ur Canadian. Don't be afraid to ask for shipping.
More stuff will become available as I keep cleaning. Have to get rid of this stuff before I move.
Last edited by Bass_Waves; 02-16-2014 at 05:40 PM.
#3
Take off the piston. Take off the bottom cap. Cut the cap and weld it to the side of the rod. Males a 4 leg stand. Take the wrist pin. Weld to the top of the rod. Get the bulb socket and such and put it on top of the wrist pin. Put the lil cover and the piston head on the very tip of it. Done.
This is how ideas come to play when I'm sniffing paint from doing retros. Dang mask does me no good lol
This is how ideas come to play when I'm sniffing paint from doing retros. Dang mask does me no good lol
#4
Junior Member
iTrader: (6)
Join Date: 01-27-11
Location: Fort Wayne, IN. USA
Posts: 402
Likes: 0
Received 0 Likes
on
0 Posts
Take off the piston. Take off the bottom cap. Cut the cap and weld it to the side of the rod. Males a 4 leg stand. Take the wrist pin. Weld to the top of the rod. Get the bulb socket and such and put it on top of the wrist pin. Put the lil cover and the piston head on the very tip of it. Done. This is how ideas come to play when I'm sniffing paint from doing retros. Dang mask does me no good lol
Sweet idea.
#12
yup. they do. sometimes they dont but all u need is like a 1mm spacer. which is nothing. i ran them with no spacers and brembos . that reminds me i have to find the brembos. they have new pads and rotors from r1. the slotted premium lol. gotta sell em too.