Mark this thread as Unsold
WTB SS Headlights
08-10-2009, 06:22 PM
#1
Senior Member
Thread Starter
Join Date: 03-04-08
Location: The 201, New Jersey
Posts: 1,614
Likes: 0
Received 0 Likes
on
0 Posts
WTB SS Headlights
I want to buy a pair of SS headlights, one of mine used to have water in it and it's starting to show corrosion. I want a pair of headlights without the yellow reflector (07+ I believe). Looking for $75 shipped for the pair, if you only have one that's fine. PM me and if someone else has the opposite side we'll work it out.
Last edited by snake890217; 08-11-2009 at 01:30 AM.
08-12-2009, 12:48 AM
#7
Senior Member
Thread Starter
Join Date: 03-04-08
Location: The 201, New Jersey
Posts: 1,614
Likes: 0
Received 0 Likes
on
0 Posts
The '07+ SS have a slight tint to them and don't have the yellow lens thing.
night bump!
night bump!
Last edited by snake890217; 08-12-2009 at 12:48 AM. Reason: Automerged Doublepost
08-12-2009, 10:22 AM
#8
Senior Member
Join Date: 07-09-08
Location: Auburn. New York
Posts: 1,381
Likes: 0
Received 0 Likes
on
0 Posts
08-12-2009, 12:52 PM
#11
Senior Member
Thread Starter
Join Date: 03-04-08
Location: The 201, New Jersey
Posts: 1,614
Likes: 0
Received 0 Likes
on
0 Posts
08-12-2009, 01:16 PM
#13
Senior Member
iTrader: (4)
Join Date: 05-19-09
Location: Severn, Maryland
Posts: 4,010
Likes: 0
Received 0 Likes
on
0 Posts
Yeah I hate that amber shield inside. I want it OUT! Might just take off my headlight and poke somehting in there to break it and shake out all the pieces!
08-29-2009, 06:28 PM
#17
Senior Member
iTrader: (4)
Join Date: 05-19-09
Location: Severn, Maryland
Posts: 4,010
Likes: 0
Received 0 Likes
on
0 Posts
Hey here's what I did, I took out my headlights, poked a screwdriver through the turn signal hole and bumped the amber lense loose. Then, I put my headlights (one at a time) in the oven at 200 degrees for like 5-10 minutes. Took them out and started to pull them apart just enough so the lense would fall out. DONE! Still warm I pushed them back together and they sealed right up!
08-29-2009, 08:45 PM
#18
Senior Member
Thread Starter
Join Date: 03-04-08
Location: The 201, New Jersey
Posts: 1,614
Likes: 0
Received 0 Likes
on
0 Posts
hmmmm maybe I'll do that after work tmrw. Did you have to put any extra sealant on them? Which side did you open the inside(by the grill) or outside (fender side)?
08-30-2009, 01:31 AM
#19
Senior Member
iTrader: (4)
Join Date: 05-19-09
Location: Severn, Maryland
Posts: 4,010
Likes: 0
Received 0 Likes
on
0 Posts
No extra sealent. I just used a screwdriver to pry open the part of the headlight closest to the fender. The "pointy" part. Some of the bottom of the headlight too. Since the headlight was still pretty warm, it sealed right back up. Just make sure you push pretty hard to get the lense back where it should be.
Thread
Thread Starter
Forum
Replies
Last Post