florida meet lets get it start
hoping that early next week i can get it running good for the meet
yea its goin to be at 1 and for sure all of us down here will be riding there together so it'll be like 9 balts from down here
damm my car is full of bad luck or its also me...i just got a call from dealer saying they wont fix the cracked manifold problem for stupid ass reasons. anyone knows where i can find a intake manifold for an 06 ss s/c?
bro till this day i still dont know...it just did. i tried again with the freaking dealer but they can care less there not gona work on it...the less work for them the better thats how they see it...no wonder this **** economy just keeps goin down worse and worse...
Member
Joined: 11-30-09
Posts: 311
Likes: 0
From: jacksonville florida
u need to contact a supervisor or someone above them... there giving u the run around bro... u need to get on it quick... but that sux... email zzp im sure they got plenty of them layin around...cheap...
chillin
Senior Member
Joined: 06-25-07
Posts: 6,003
Likes: 0
From: Kissimmee, Fl
I'm trying to bring some company. Not sure if it's gonna happen. Either way. I'm golden to go. See y'all there.
Joe, do you have some CAB's? Or a shifter cable bracket? The one that mounts to the top of the tranny case under the fuse box?
Joe, do you have some CAB's? Or a shifter cable bracket? The one that mounts to the top of the tranny case under the fuse box?
I may have that shifter bracket, i'll check tomorrow, but no guarantees, I think I left it on the trans when I sold it.
As far as CAB's, I have one pair of used Intense poly ones that are not too good anymore, or I could make you a set of the spherical ones I ran. Downside to that is they are quite expensive in comparison, as they take me a long time to make by hand. I wanted to do a run of them on the CNC stuff at work, but I couldn't get enough interest at the price point, then John started offering them separately through OTTP when they contacted me about a set...
I could do it though, believe I still have a pair of the bearings ($40 right there alone), i'll have to check at work though.
As far as CAB's, I have one pair of used Intense poly ones that are not too good anymore, or I could make you a set of the spherical ones I ran. Downside to that is they are quite expensive in comparison, as they take me a long time to make by hand. I wanted to do a run of them on the CNC stuff at work, but I couldn't get enough interest at the price point, then John started offering them separately through OTTP when they contacted me about a set...
I could do it though, believe I still have a pair of the bearings ($40 right there alone), i'll have to check at work though.
Member
Joined: 04-16-09
Posts: 200
Likes: 0
From: Pembroke Pines, FL
1. nastyfastnx
2. dr balt
3. usdm08
4. blazino7ss
5. jonathan923
6. 1slo ion
7. stonny9
8. DFZ24
9. ovcuban
10. TheAnswer07
Ill try to get some of the cobalts around here to go. See you guys then...
2. dr balt
3. usdm08
4. blazino7ss
5. jonathan923
6. 1slo ion
7. stonny9
8. DFZ24
9. ovcuban
10. TheAnswer07
Ill try to get some of the cobalts around here to go. See you guys then...
Thread Starter
Senior Member
Joined: 07-21-08
Posts: 522
Likes: 0
From: miami
im gonna check too, i know i have a extra bracket just have to look for it
Senior Member
Joined: 06-25-07
Posts: 6,003
Likes: 0
From: Kissimmee, Fl
I may have that shifter bracket, i'll check tomorrow, but no guarantees, I think I left it on the trans when I sold it.
As far as CAB's, I have one pair of used Intense poly ones that are not too good anymore, or I could make you a set of the spherical ones I ran. Downside to that is they are quite expensive in comparison, as they take me a long time to make by hand. I wanted to do a run of them on the CNC stuff at work, but I couldn't get enough interest at the price point, then John started offering them separately through OTTP when they contacted me about a set...
I could do it though, believe I still have a pair of the bearings ($40 right there alone), i'll have to check at work though.
As far as CAB's, I have one pair of used Intense poly ones that are not too good anymore, or I could make you a set of the spherical ones I ran. Downside to that is they are quite expensive in comparison, as they take me a long time to make by hand. I wanted to do a run of them on the CNC stuff at work, but I couldn't get enough interest at the price point, then John started offering them separately through OTTP when they contacted me about a set...
I could do it though, believe I still have a pair of the bearings ($40 right there alone), i'll have to check at work though.
Tax returns will hopefully come back in a few weeks. That'll cover my Stage 1 axles and hopefully the rest of my turbo build stuff plus some cash left over.
Member
Joined: 11-30-09
Posts: 311
Likes: 0
From: jacksonville florida
ya imma try and race the other twincharged ion cause the redlineforums is wanting to see that go down... i will turn my boost down just so it be a close race... then ill do a run at regular boost...
