GRAVANA BG COIL-OVER SUSPENSION Pre-Order Sale
#52
Member
Thread Starter
Join Date: 01-03-05
Location: Santa Clarita
Posts: 336
Likes: 0
Received 0 Likes
on
0 Posts
The Pre-Order sets are goping into production in 2-3 weeks. The boat ride is @ 3-4 weeks, unless there are any customs delays. 7 weeks out is a realistic ETA from now. If you Pre-Ordered already, we expect to be shipping these to you in @ 7 weeks.
If you did not yet place your Pre-Order, you have less than 2 weeks to get it in...
If you did not yet place your Pre-Order, you have less than 2 weeks to get it in...
#53
Senior Member
Join Date: 10-12-06
Location: Saskatchewan
Posts: 3,089
Likes: 0
Received 0 Likes
on
0 Posts
thread started in January (edit: December), coil overs not ready until August
does that seem a bit crazy to anyone else? It's not exactly a twin screw swap. I mean you can make a baby in that much time......
does that seem a bit crazy to anyone else? It's not exactly a twin screw swap. I mean you can make a baby in that much time......
#54
Member
Thread Starter
Join Date: 01-03-05
Location: Santa Clarita
Posts: 336
Likes: 0
Received 0 Likes
on
0 Posts
Thanks.
#56
Member
Thread Starter
Join Date: 01-03-05
Location: Santa Clarita
Posts: 336
Likes: 0
Received 0 Likes
on
0 Posts
No problem. I wish the enthusiasm was there to front-line it all along. We sponsored the TPR Magazine Cobalt SS and they love the coil-over set-up and the Pillow Ball Mount Camber Plates. Sometimes, it just takes a few people using the product to share their experience and that opens the floodgate. Other times (like this), it takes more.
Jim
Jim
#57
Senior Member
Join Date: 07-28-05
Location: Calgary, AB, Canada
Posts: 521
Likes: 0
Received 0 Likes
on
0 Posts
No problem. I wish the enthusiasm was there to front-line it all along. We sponsored the TPR Magazine Cobalt SS and they love the coil-over set-up and the Pillow Ball Mount Camber Plates. Sometimes, it just takes a few people using the product to share their experience and that opens the floodgate. Other times (like this), it takes more.
Jim
Jim
#58
Member
Thread Starter
Join Date: 01-03-05
Location: Santa Clarita
Posts: 336
Likes: 0
Received 0 Likes
on
0 Posts
We are flexible and understanding when it comes to things like that.
#61
Senior Member
Join Date: 04-11-04
Location: patterson, ca
Posts: 2,175
Likes: 0
Received 0 Likes
on
0 Posts
i would so get these, B+G are by far one of the best companies out there as far as suspension goes. they make quality stuff. hey what happend to their springs they had for the cobalt ss s/c?
#62
They rather have people buy a coil over system then the springs I'm sure. I don't blame them, coil overs is the only way to go IMO.
#63
I emailed the contact address at the Gravana site and never heard back about where things stand for the Redline at this point. I don't think any of us redline guys would mind drilling into things if we were able to get some reinforcement plates or something to help get these things retrofitted. Regardless, the Redline needs support, too!
#64
Senior Member
whats the spring rate on these?
i'm not looking for much of a lower stance(charge pipe clearance issue) but i would love to have a stiffer ride, much like my STi....i just like that connected feeling.
i'm not looking for much of a lower stance(charge pipe clearance issue) but i would love to have a stiffer ride, much like my STi....i just like that connected feeling.
#65
Senior Member
Join Date: 05-17-07
Location: Ft. Hood
Posts: 476
Likes: 0
Received 0 Likes
on
0 Posts
coming up with 1200 is not very easy for me to do. Is there any way to make payments and be put on the list??
#66
it says on the website that ride height will vary from 0 - 3 inches. is this for front and rear? and you can adjust the drop to somewhere in between also? just wanted to clarify, thanks for bearing with me.
#67
could i install these coilovers myself? how do you adjust the ride height/how long does it take to do that? also, are the Optional Adjustable Pillowball Camber Plates necessary? thank you.
#68
Senior Member
Join Date: 04-11-04
Location: patterson, ca
Posts: 2,175
Likes: 0
Received 0 Likes
on
0 Posts
if your good with tools yes u can install them, they are fully adjustable from 0-3" so u can set it to half inch drop if u want or go to a 1. 1.3 1.5 1.6 what ever u want up to 3 inch max.
#70
Senior Member
Join Date: 04-11-04
Location: patterson, ca
Posts: 2,175
Likes: 0
Received 0 Likes
on
0 Posts
seriously. much long awaited. theres better ride smoother and softer than a caddy on the softest setting, and handle like its on Enzo on the stiffest settings.
#72
Senior Member
Join Date: 02-07-06
Location: NE Houston
Posts: 1,236
Likes: 0
Received 0 Likes
on
0 Posts
#74
Senior Member
Join Date: 04-11-04
Location: patterson, ca
Posts: 2,175
Likes: 0
Received 0 Likes
on
0 Posts