Cobalt SS Network
0 2020/10/15 10:08:24
0 2020/09/26 15:48:28
0 2020/09/26 15:48:21
0 2020/09/14 11:42:17
Underside, angle 3
Underside, angle 3
0 2020/09/14 06:20:04
Angle 2
Angle 2
0 2020/09/14 06:19:59
Primer + Paint + Clear Coat + 45 minute dry time
Primer + Paint + Clear Coat + 45 minute dry time
0 2020/09/14 06:19:54
Masking with a few feathering techniques
Masking with a few feathering techniques
0 2020/09/14 06:19:50
0 2020/09/08 07:48:27
0 2020/09/08 07:48:20
0 2020/09/08 07:46:16
0 2020/09/08 07:46:11
Close up
Close up
0 2020/09/04 11:31:27
Center cap
Center cap
0 2020/09/04 09:26:37
2 coats 2K clear coat gloss
2 coats 2K clear coat gloss
0 2020/09/04 09:26:06
3 coats of paint
3 coats of paint
0 2020/09/04 09:25:30
2 coats of Primer
2 coats of Primer
0 2020/09/04 09:25:08
0 2020/08/26 11:24:23
0 2020/08/26 11:24:09
0 2020/08/26 11:23:56
0 2020/08/13 14:26:44
0 2020/08/13 14:22:23
0 2020/08/13 14:22:18
0 2020/08/11 10:31:11
0 2020/08/01 13:41:52
Looking inside the door
Looking inside the door
0 2020/08/01 13:40:57
Completed, even redid the wiring to clean it up.
Completed, even redid the wiring to clean it up.
0 2020/08/01 13:40:07
Panel, vapour barrier off. Started to clean.
Panel, vapour barrier off. Started to clean.
0 2020/08/01 13:38:50
0 2020/07/08 10:56:29
0 2020/07/08 10:56:27
0 2020/07/08 10:56:25
0 2020/07/06 06:59:09
0 2020/06/21 09:58:20
Driver side. Used flash this time to get a better picture.
Driver side. Used flash this time to get a better picture.
0 2020/06/15 07:21:48
Managed to finish the sound deadening and wire in the new speakers at dusk. Passenger side.
Managed to finish the sound deadening and wire in the new speakers at dusk. Passenger side.
0 2020/06/15 07:20:59
Stock vs new. The stock's complete height is just the height of the driver and the coils on the new one lol
Stock vs new. The stock's complete height is just the height of the driver and the coils on the new one lol
0 2020/06/15 07:20:00
The new (badass) speakers
The new (badass) speakers
0 2020/06/15 07:19:42
Got under the modular parts, as well as putting in the holes for the bolts where they need to go.
Got under the modular parts, as well as putting in the holes for the bolts where they need to go.
0 2020/06/15 07:19:09
Prepped the rear deck and started the sound deadening process here
Prepped the rear deck and started the sound deadening process here
0 2020/06/15 07:18:39
Mostly finished seat. The 2 middle bolts are 19mm, the two end ones are 18mm. I had to go to the store and buy a 60cm racheting breaker bar to get those 18mm bolts out. Even with penetrating fluid it was a bitch. I did finish the entire seat though afterwards.
Mostly finished seat. The 2 middle bolts are 19mm, the two end ones are 18mm. I had to go to the store and buy a 60cm racheting breaker bar to get those 18mm bolts out. Even with penetrating fluid it was a bitch. I did finish the entire seat though afterwards.
0 2020/06/15 07:16:34