Vendor Help! 2.85" pulley!
360 L337 User
Joined: 08-11-05
Posts: 7,454
Likes: 0
From: Philadelphia, Pa
Originally Posted by johnkb8
^^ we want the stock lookin pulley type
stop complaining and just get a 2,8. they make them to look just like the 3.0 somewhere you can even get one that has the 77.9 or whatever in mm stamped right on it.
Senior Member
Joined: 08-17-06
Posts: 2,580
Likes: 0
From: Cadogan, PA
Originally Posted by R33P3R007
stop complaining and just get a 2,8. they make them to look just like the 3.0 somewhere you can even get one that has the 77.9 or whatever in mm stamped right on it.
i asked that same question earlier today in another thread!
Thread Starter
Senior Member
Joined: 03-21-06
Posts: 7,917
Likes: 2
From: CT
Originally Posted by splink
that would be cobalt addiction's 2.8 pulley.
i asked that same question earlier today in another thread!
i asked that same question earlier today in another thread!
If I can't get a vendor to make this 2.85 I might just go with that and a tune.
If the IDC is high, i'll lower the rev limiter which is what i don't want to do.
Senior Member
Joined: 08-13-05
Posts: 5,733
Likes: 1
From: the glove
Originally Posted by patathSS
They are rated to flow that on a standard fuel rail pressure setup. Since an injector is pulse controlled, when you have greater pressure behind it, you are forcing more fuel through the pulse. Find any injector calculator and on order to compute your actual injector flow you need to know what your fuel rail pressure is. If your philosoph was true than boost-a-pump would be out of business.
i've said it before and i'll sat it agen....with a increased red line(6800 and up) a 42lb injecter will not support a 2.7pully safely
Thread Starter
Senior Member
Joined: 03-21-06
Posts: 7,917
Likes: 2
From: CT
Originally Posted by 06black
Thanks pat....you saved me from blowing up on yet another one of these threds!
i've said it before and i'll sat it agen....with a increased red line(6800 and up) a 42lb injecter will not support a 2.7pully safely
i've said it before and i'll sat it agen....with a increased red line(6800 and up) a 42lb injecter will not support a 2.7pully safely
We all know a 2.7" pulley and 42lb injectors are no good.
Come on vendors help out a brother from another mother.
Senior Member
Joined: 09-14-05
Posts: 6,697
Likes: 0
From: Phx, AZ
Originally Posted by CTCOBALTSSS
Yeah bro but we are talking about a 2.85" pulley. That's what this thread is all about.
We all know a 2.7" pulley and 42lb injectors are no good.
Come on vendors help out a brother from another mother.
We all know a 2.7" pulley and 42lb injectors are no good.
Come on vendors help out a brother from another mother.
Thread Starter
Senior Member
Joined: 03-21-06
Posts: 7,917
Likes: 2
From: CT
Originally Posted by OniMirage
yeah come on all you .net ***** #$%^ers get in on this yo
That's it, i'm calling ZZPerformance, Billetflow and Cobalt Addiction to see what we can do.
Senior Member
Joined: 09-14-05
Posts: 6,697
Likes: 0
From: Phx, AZ
Originally Posted by CTCOBALTSSS
Exactly, lets show them that there is an interest. I know I want one like tomorrow!
That's it, i'm calling ZZPerformance, Billetflow and Cobalt Addiction to see what we can do.
That's it, i'm calling ZZPerformance, Billetflow and Cobalt Addiction to see what we can do.
Senior Member
Joined: 10-08-05
Posts: 751
Likes: 0
From: Metro Detroit
There is someone on the Red Lineforums that is going to be making different size pulleys that fit the GM hub. I'm sending him my pulley today so he can measure it up and get started making the pulleys. I'm going to get a 2.9". But he can make other sizes too.
http://tinyurl.com/ymxzsr
http://tinyurl.com/ymxzsr
Thread Starter
Senior Member
Joined: 03-21-06
Posts: 7,917
Likes: 2
From: CT
Originally Posted by max_boost
There is someone on the Red Lineforums that is going to be making different size pulleys that fit the GM hub. I'm sending him my pulley today so he can measure it up and get started making the pulleys. I'm going to get a 2.9". But he can make other sizes too.
http://tinyurl.com/ymxzsr
http://tinyurl.com/ymxzsr
He only has 8 posts though are you sure he is reliable?
Thread Starter
Senior Member
Joined: 03-21-06
Posts: 7,917
Likes: 2
From: CT
Originally Posted by Jim@Tagracecraft
hey Guys I think i might be able to help you fellows out with a 2.85 pulley
I would need a minimum of 10 pulleys to get anything started
Pm me and let me know
jim
I would need a minimum of 10 pulleys to get anything started
Pm me and let me know
jim
1. Me
2.
3.
4.
5.
6.
7.
8.
9.
10.
Senior Member
Joined: 08-13-05
Posts: 5,733
Likes: 1
From: the glove
I think BF's 2.9 is as good as it gets!!!
rember that Doug(BiletFlow) mesures his pullys differant so it may be closer to the size you want..
call them and ask!!....its weird that nobody answered.....you got the rite number?....
i guess thats why i just call his cell phone...but the shop phone is
313-388-8228
rember that Doug(BiletFlow) mesures his pullys differant so it may be closer to the size you want..
call them and ask!!....its weird that nobody answered.....you got the rite number?....
i guess thats why i just call his cell phone...but the shop phone is
313-388-8228
Senior Member
Joined: 10-08-05
Posts: 751
Likes: 0
From: Metro Detroit
Originally Posted by 06black
I think BF's 2.9 is as good as it gets!!!
rember that Doug(BiletFlow) mesures his pullys differant so it may be closer to the size you want..
call them and ask!!....its weird that nobody answered.....you got the rite number?....
i guess thats why i just call his cell phone...but the shop phone is
313-388-8228
rember that Doug(BiletFlow) mesures his pullys differant so it may be closer to the size you want..
call them and ask!!....its weird that nobody answered.....you got the rite number?....
i guess thats why i just call his cell phone...but the shop phone is
313-388-8228
Thread Starter
Senior Member
Joined: 03-21-06
Posts: 7,917
Likes: 2
From: CT
Originally Posted by nherbst454
Just thought I should say hi and let folks know that I will be getting a GM Stage 2 2.8" pulley from a Redline owner soon to get some dimensions from then I will be able to make any size pulley you guys would like.
I've been making pulleys for about 2 years now and have quite a few happy customers so there should be no problem making ANY size you'd like, I also don't have any minimum order sizes!
Feel free to pm me with questions
~Nate
NHERBST454 Pulleys
I've been making pulleys for about 2 years now and have quite a few happy customers so there should be no problem making ANY size you'd like, I also don't have any minimum order sizes!
Feel free to pm me with questions
~Nate
NHERBST454 Pulleys