Z06 Rear Valance
#32
Senior Member
Join Date: 05-11-07
Location: Bourbonnais IL
Posts: 4,741
Likes: 0
Received 0 Likes
on
0 Posts
#35
Senior Member
Join Date: 01-24-06
Location: Warranty Chevrolet, Maryland
Posts: 765
Likes: 0
Received 0 Likes
on
0 Posts
I got a closer look at one on a lift, your right it is 2 pieces. SS/SC with a corvetter rear valance, G5 deck lid, and SS/TC wheels . Oh my god hot looking.
#38
Senior Member
iTrader: (5)
Very nice looking 'balt. Honestly thought the back looks like a ss/na to me at a glance. Most people wouldn't appreciate 'cause they'd figure it's just an ss/na and wouldn't bother too look. Just my opinion. Overall it does look pretty sick though. Especially with the Z06 wheels. I want them.
#41
Senior Member
Thread Starter
Join Date: 09-28-06
Location: Columbus, OH - Wilkes Barre, PA
Posts: 2,288
Likes: 0
Received 0 Likes
on
0 Posts
I am gettin my prices today!!
Heres a rough draft of the tails and trunk the wing be be gone after this project
Heres a rough draft of the tails and trunk the wing be be gone after this project
Last edited by 2FST4U; 02-01-2008 at 12:31 PM. Reason: Automerged Doublepost
#42
Senior Member
Join Date: 03-30-06
Location: Exit 29, NY
Posts: 3,014
Likes: 0
Received 0 Likes
on
0 Posts
I totally want the rear end... wtf... ugh.... Its even got the exhaust set up that I want and everything... o well.. good luck and I guess I will just stick with my RKSport G5 Rear Valance....
later
later
#43
New Member
Join Date: 11-20-07
Location: Ontario, Canada
Posts: 102
Likes: 0
Received 0 Likes
on
0 Posts
Just so you know they do make an "exhaust facia overlay" for the rear of the C5 Vette.
http://corvette-enhancements.com/c5_overlay.php
It would likely be a lot easier to mold in, then using the factory bumper.
It sure is an expensive piece of plastic though !!
Later,
Brad
http://corvette-enhancements.com/c5_overlay.php
It would likely be a lot easier to mold in, then using the factory bumper.
It sure is an expensive piece of plastic though !!
Later,
Brad
#44
Senior Member
Join Date: 02-08-08
Location: Missouri
Posts: 512
Likes: 0
Received 0 Likes
on
0 Posts
#45
Banned
Join Date: 02-09-07
Location: I'm currently busy putting 10,000 kids on your mothers face!!!
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
that's a very very bad idea for this reason.. If done like that the mufflers would be directly under the gas tank. And wow doesn't that sound like a horrible idea. For what you would achieve and to do it properly it's not worth it. I know i wouldn't want to have a exhaust set up like running butting against my gas tank thats for damn sure.
#46
Senior Member
Thread Starter
Join Date: 09-28-06
Location: Columbus, OH - Wilkes Barre, PA
Posts: 2,288
Likes: 0
Received 0 Likes
on
0 Posts
what about runnin around it?
I will throw it on a lift when it gets warm and look
WOW $400 my buddy gets discounts from his dads shop so I'll see what i can get
I will throw it on a lift when it gets warm and look
Just so you know they do make an "exhaust facia overlay" for the rear of the C5 Vette.
http://corvette-enhancements.com/c5_overlay.php
It would likely be a lot easier to mold in, then using the factory bumper.
It sure is an expensive piece of plastic though !!
Later,
Brad
http://corvette-enhancements.com/c5_overlay.php
It would likely be a lot easier to mold in, then using the factory bumper.
It sure is an expensive piece of plastic though !!
Later,
Brad
Last edited by 2FST4U; 02-28-2008 at 11:27 AM. Reason: Automerged Doublepost