Couple pictures of my progress

Reply Subscribe

Thread Tools

Search this Thread

Aug 26, 2006 | 05:31 PM

#26

SSinPhilly

Senior Member

Joined: 08-14-06

Posts: 796

Likes: 0

From: Philly

once clean it'll look 10x's better

Aug 26, 2006 | 06:40 PM

#27

l Sh1ft l

Senior Member

Joined: 04-24-06

Posts: 2,191

Likes: 0

From: Canton Ohio

Quote:

Originally Posted by Blackout06LS

I don't run with my 16s on. And whats the track conditions for the time you ran, etc? 90 degrees humid and a sucky prep on the track(they didn't even mop like they should). So I lost traction quite often.

There is a lot that goes into the factor, and I just don't prefer big rims...what's wrong with that taste? And your looking at a time of a stock LS yet is your time stock or when you had mods?

I wasn't aware 17's were considered big.

Aug 26, 2006 | 06:44 PM

#28

marerick007

Senior Member

Joined: 06-30-06

Posts: 2,647

Likes: 0

From: Langley AFB, VA

Quote:

Originally Posted by l Sh1ft l

looks like a shitty weld job.....

My thoughts exactly...

Aug 26, 2006 | 09:14 PM

#29

06cobaltls

Senior Member

Joined: 08-18-06

Posts: 555

Likes: 0

From: marion ohio

Quote:

Originally Posted by marerick007

My thoughts exactly...

everyone is to damn pickey, if that is what works then it works, and that is coming from an experienced welder, it may not look pretty, but it gets the job done for the time being

Aug 26, 2006 | 09:38 PM

#30

tonio5555

Senior Member

Joined: 11-10-05

Posts: 2,477

Likes: 0

From: USA

Looking good, could you tell us some more about your SAFC II setup? How much did it cost and how difficult was the install?

Aug 27, 2006 | 06:57 AM

#31

IonNinja

Senior Member

Joined: 07-29-05

Posts: 7,915

Likes: 0

From: AZ

Quote:

Originally Posted by 06cobaltls

everyone is to damn pickey, if that is what works then it works, and that is coming from an experienced welder, it may not look pretty, but it gets the job done for the time being

I just don't get why you welded two mufflers together like that

you can keep down the amount of noise with a properly size resonator.

and we're car guys...of course we're picky.

Sep 3, 2006 | 09:30 PM

#32

Boosted_SS

Banned

Joined: 05-16-06

Posts: 911

Likes: 0

From: STEELER COUNTRY

dude where did you mount your sending unit for the oil pressure guage??? i'm installing one in the next week and i'm at a loss as to where to look on the plock for a plug to remove

Sep 3, 2006 | 10:10 PM

#33

L.P.

Senior Member

Joined: 08-06-06

Posts: 1,529

Likes: 0

From: Clintwood, VA

My cavy 2.2 ecotec saw a 14.9 at 93 with a 50 shot. BTW it was an auto.

Sep 3, 2006 | 10:15 PM

#34

SSinPhilly

Senior Member

Joined: 08-14-06

Posts: 796

Likes: 0

From: Philly

i was 14.5 99 mph with bolt ons and a zex 75 shot

Sep 3, 2006 | 10:15 PM

#35

SSinPhilly

Senior Member

Joined: 08-14-06

Posts: 796

Likes: 0

From: Philly

auto also

Sep 3, 2006 | 10:37 PM

#36

L.P.

Senior Member

Joined: 08-06-06

Posts: 1,529

Likes: 0

From: Clintwood, VA

the 2.2 ecotec isn't as sluggish as some people think..if you remember josh with the turbo 2.2 eating transams you'd understand.

Sep 15, 2006 | 06:53 PM

#37

cobaltLS4dr

New Member

Joined: 08-13-06

Posts: 103

Likes: 0

From: Dunedin Florida

i have 2 questions firt, what is a SAFCII? and second, how did you mod the B&M and how much did it cost? or should i just go out and get the one for the 2.2? and who makes that?