Philly Area Chat thread
Thread Starter
Senior Member
iTrader: (5)
Joined: 12-30-07
Posts: 13,485
Likes: 1
From: Williamstown, NJ
Okay. I'll be working just about everyday this week and I'll be doing stuff new years eve/day. Not sure what's going on this weekend, but I'll let ya know. You got a spot to do it?
Senior Member
Joined: 10-01-08
Posts: 4,790
Likes: 1
From: Philthydelphia, PA
yo Jimmy do you want to do a dig run and a roll next weekend against your stockie?
also i have a question for this non active philly thread. you think its possible on the same day i go get my dyno tune i can install my injectors, plugs and hub/pulley but as long as i didnt put a load on the motor(put more than 2 psi boost) i'll be fine. because he said he would charge 650 for them to install it 400 for just the dyno tune 4 runs... so 250.00 to install... someone anyone? i would like to save 250 though
also i have a question for this non active philly thread. you think its possible on the same day i go get my dyno tune i can install my injectors, plugs and hub/pulley but as long as i didnt put a load on the motor(put more than 2 psi boost) i'll be fine. because he said he would charge 650 for them to install it 400 for just the dyno tune 4 runs... so 250.00 to install... someone anyone? i would like to save 250 though
Last edited by 06SS ALL DAY; Dec 30, 2008 at 12:08 PM. Reason: werd
Senior Member
Joined: 10-01-08
Posts: 4,790
Likes: 1
From: Philthydelphia, PA
not putting a load on the motor shouldnt hurt though... ahhh f it, i'll put the injectors and plugs in in there park n lot before the open i guess and just say hey all i need installed is the hub and pulley
Senior Member
Joined: 12-30-07
Posts: 1,835
Likes: 0
From: PHILADELPHIA
yo Jimmy do you want to do a dig run and a roll next weekend against your stockie?
also i have a question for this non active philly thread. you think its possible on the same day i go get my dyno tune i can install my injectors, plugs and hub/pulley but as long as i didnt put a load on the motor(put more than 2 psi boost) i'll be fine. because he said he would charge 650 for them to install it 400 for just the dyno tune 4 runs... so 250.00 to install... someone anyone? i would like to save 250 though
also i have a question for this non active philly thread. you think its possible on the same day i go get my dyno tune i can install my injectors, plugs and hub/pulley but as long as i didnt put a load on the motor(put more than 2 psi boost) i'll be fine. because he said he would charge 650 for them to install it 400 for just the dyno tune 4 runs... so 250.00 to install... someone anyone? i would like to save 250 though
i was tryin to find if a shop would do it in case , we didn have time to do ourselves
Last edited by cobaltssredtint; Dec 30, 2008 at 01:30 PM. Reason: Automerged Doublepost
Senior Member
Joined: 12-30-07
Posts: 1,835
Likes: 0
From: PHILADELPHIA
nah....its one or both...when you go smaller than 2.7 you need a tensioner..kinda like you will also need a mahined snout.......but stage 2 belt is needed for any pulley smaller then stock basically..yea i hope the clutch doesn do the same thing
Senior Member
Joined: 10-01-08
Posts: 4,790
Likes: 1
From: Philthydelphia, PA
well ok so tomorrow assuming i get paid which i should. i will order stage 2 belt, 42 injectors/harness, ngk plugs, thaaan my following paycheck i will take a visit to TTP to get dynoed... does anyone want to ride with me?
Thread Starter
Senior Member
iTrader: (5)
Joined: 12-30-07
Posts: 13,485
Likes: 1
From: Williamstown, NJ
^^on what?
And was anyone on here the yellow ss/sc with the low-pro that I was behind/next to on 95 north in traffic around 245-3? Whoever it is, you were a smidge anti-social haha
And was anyone on here the yellow ss/sc with the low-pro that I was behind/next to on 95 north in traffic around 245-3? Whoever it is, you were a smidge anti-social haha
Senior Member
Joined: 12-30-07
Posts: 1,835
Likes: 0
From: PHILADELPHIA
