Mark this thread as Unsold
For Sale AIS Stage 1 Water/Meth Kit and TB Spacer
Thread Starter
Senior Member
iTrader: (4)
Joined: 02-18-07
Posts: 14,089
Likes: 0
From: Whittier, Ca
AIS Stage 1 Water/Meth Kit and TB Spacer
Anyone looking for a meth kit? I'm not gonna use it it anymore, never installed on my car, but it is used(barely) Junior(euthanasia [on ss.net]) had it installed on one of his mustang's, got it all setup to work and then took it off the car. It's an AIS stage 1 kit with an M10(10gph) nozzle with the "old" smaller 1.5(might be only 1gallon, pretty sure it's 1.5 tho) gallon tank, looking for $200 Shipped(48 States, international extra) OBO
also have a TB Spacer LINK OTTP TB spacer with 1/8" npt tap for meth or nitrous (had it on the car for about 1000miles never sprayed anything through it tho, payed $78.99 for it less than a year ago) will let it go for $50 Shipped(48 States, international extra) OBO
1 x Throttle Body Spacer With 1/8" NPT Tap () = $78.99
Throttle Body Fitted On Vehicle Stock +
heres vids of it working, get a pic up later
Meth kit with M10(10gph) nozzle 
Meth kit with M10(10gph) nozzle
PayPal Only, Thanks
also have a TB Spacer LINK OTTP TB spacer with 1/8" npt tap for meth or nitrous (had it on the car for about 1000miles never sprayed anything through it tho, payed $78.99 for it less than a year ago) will let it go for $50 Shipped(48 States, international extra) OBO
1 x Throttle Body Spacer With 1/8" NPT Tap () = $78.99
Throttle Body Fitted On Vehicle Stock +
heres vids of it working, get a pic up later
Meth kit with M10(10gph) nozzle Meth kit with M10(10gph) nozzlePayPal Only, Thanks
yes you'll need a tune, a smaller nozzle is recommended(you wont need bigger than a M5 {5GPH} nozzle), some where to mount the nozzle(throttle body spacer and/or supercharger spacer are the easiest)...
This is off the AIS website(what one of their brand new kits includes) The parts marked in bold are what the kit was sold to me with/what i am selling. never installed or used it myself, but i did hook it up to power and turned boost switch all the way down and it worked.
so you'll need a fuse/fuse holder, wire, connectors...Heres the best install instructions i could find, this is for a cooling mist kit, but they all install pretty similarl http://www.coolingmist.com/instructions/CMS1deluxe.pdf
and heres a how to on installing an activation light to ur kit so u know when its on https://www.cobaltss.net/forums/how-...system-123603/
This is off the AIS website(what one of their brand new kits includes) The parts marked in bold are what the kit was sold to me with/what i am selling. never installed or used it myself, but i did hook it up to power and turned boost switch all the way down and it worked.
System Contents Include:
*
Custom molded 3 gallon tank designed specifically for our pump I have the older kit that has the smaller 1.5 gal tank
*
All new 250 psi pump with EPDM seals for use with 100% methanol I believe(due to being the older kit) this is a 150psi pump
*
1-25 psi adjustable boost activated switch
*
Nickel plated threaded injector holder
*
Interchangeable injector sized to application The nozzle I have for it is a M10(10gph) which is too big for a cobalt, but can be easily changed
*
Heavy duty one-way check valve
*
20 ft of black high pressure vacuum tubing
*I have about 50' vacuum/water-meth line
20 ft of black high pressure water methanol tubing
*
20 ft of electrical wire
*
LED activation light
*
Grounding wire with grounding screw and terminal
*
Vacuum tee fitting
*
Two rubber grommets
*
Water resistant fuse holder with fuse
*
Four butt connectors
*
10 each 8" zip ties (large)
*
5 each 4" zip ties (small)
*
Two black anodized aluminum tank straps
*
Detailed instructions with pictures
*
AIS sticker
*
Custom molded 3 gallon tank designed specifically for our pump I have the older kit that has the smaller 1.5 gal tank
*
All new 250 psi pump with EPDM seals for use with 100% methanol I believe(due to being the older kit) this is a 150psi pump
*
1-25 psi adjustable boost activated switch
*
Nickel plated threaded injector holder
*
Interchangeable injector sized to application The nozzle I have for it is a M10(10gph) which is too big for a cobalt, but can be easily changed
*
Heavy duty one-way check valve
*
20 ft of black high pressure vacuum tubing
*I have about 50' vacuum/water-meth line
20 ft of black high pressure water methanol tubing
*
20 ft of electrical wire
*
LED activation light
*
Grounding wire with grounding screw and terminal
*
Vacuum tee fitting
*
Two rubber grommets
*
Water resistant fuse holder with fuse
*
Four butt connectors
*
10 each 8" zip ties (large)
*
5 each 4" zip ties (small)
*
Two black anodized aluminum tank straps
*
Detailed instructions with pictures
*
AIS sticker
so you'll need a fuse/fuse holder, wire, connectors...Heres the best install instructions i could find, this is for a cooling mist kit, but they all install pretty similarl http://www.coolingmist.com/instructions/CMS1deluxe.pdf
and heres a how to on installing an activation light to ur kit so u know when its on https://www.cobaltss.net/forums/how-...system-123603/
Last edited by RooTBeeR; Oct 4, 2010 at 10:24 PM.
Thread Starter
Senior Member
iTrader: (4)
Joined: 02-18-07
Posts: 14,089
Likes: 0
From: Whittier, Ca
Thread Starter
Senior Member
iTrader: (4)
Joined: 02-18-07
Posts: 14,089
Likes: 0
From: Whittier, Ca
the meth/water mix cools the intake charge by being sprayed in the the intake air charge itself(after the MAF sensor). it is totally seperate from the intercooler system for the blower which is a coolant style system.
Last edited by RooTBeeR; Sep 18, 2010 at 09:15 PM.
Thread Starter
Senior Member
iTrader: (4)
Joined: 02-18-07
Posts: 14,089
Likes: 0
From: Whittier, Ca
This is off the AIS website(what one of their brand new kits includes) The parts marked in bold are what the kit was sold to me with/what i am selling. never installed or used it myself, but i did hook it up to power and turned boost switch all the way down and it worked.
System Contents Include:
*
Custom molded 3 gallon tank designed specifically for our pump I have the older kit that has the smaller 1.5 gal tank
*
All new 250 psi pump with EPDM seals for use with 100% methanol I believe(due to being the older kit) this is a 150psi pump
*
1-25 psi adjustable boost activated switch
*
Nickel plated threaded injector holder
*
Interchangeable injector sized to application The nozzle I have for it is a M10(10gph) which is too big for a cobalt, but can be easily changed
*
Heavy duty one-way check valve
*
20 ft of black high pressure vacuum tubing
*I have about 50' vacuum/water-meth line
20 ft of black high pressure water methanol tubing
*
20 ft of electrical wire
*
LED activation light
*
Grounding wire with grounding screw and terminal
*
Vacuum tee fitting
*
Two rubber grommets
*
Water resistant fuse holder with fuse
*
Four butt connectors
*
10 each 8" zip ties (large)
*
5 each 4" zip ties (small)
*
Two black anodized aluminum tank straps
*
Detailed instructions with pictures
*
AIS sticker
*
Custom molded 3 gallon tank designed specifically for our pump I have the older kit that has the smaller 1.5 gal tank
*
All new 250 psi pump with EPDM seals for use with 100% methanol I believe(due to being the older kit) this is a 150psi pump
*
1-25 psi adjustable boost activated switch
*
Nickel plated threaded injector holder
*
Interchangeable injector sized to application The nozzle I have for it is a M10(10gph) which is too big for a cobalt, but can be easily changed
*
Heavy duty one-way check valve
*
20 ft of black high pressure vacuum tubing
*I have about 50' vacuum/water-meth line
20 ft of black high pressure water methanol tubing
*
20 ft of electrical wire
*
LED activation light
*
Grounding wire with grounding screw and terminal
*
Vacuum tee fitting
*
Two rubber grommets
*
Water resistant fuse holder with fuse
*
Four butt connectors
*
10 each 8" zip ties (large)
*
5 each 4" zip ties (small)
*
Two black anodized aluminum tank straps
*
Detailed instructions with pictures
*
AIS sticker
so you'll need a fuse/fuse holder, wire, connectors...Heres the best install instructions i could find, this is for a cooling mist kit, but they all install pretty similarl http://www.coolingmist.com/instructions/CMS1deluxe.pdf
and heres a how to on installing an activation light to ur kit so u know when its on https://www.cobaltss.net/forums/how-...system-123603/
Junior Member
Joined: 02-22-10
Posts: 448
Likes: 0
From: Frederick MD
Bump!
