new custom exhaust
Thread Starter
Joined: 05-04-08
Posts: 36,934
Likes: 2
From: The 405
new custom exhaust
Its gonna be badass. Going to be getting the CIA header/dp with cat, and then a custom 2.5" cat back which will consist of these two bad boys.
http://store.summitracing.com/largei...pe-12640_w.jpg
That will be going in the location of the stock resonator.
http://store.summitracing.com/largei...pe-35109_w.jpg
And that will obviously be my tip and the end of the piping.
So cliff notes. CIA header dp w/ cat, magnaflow 2.5" inlet outlet with a 6"x27" case with a 33" over all length resonator/muffler, magnaflow 2.5"inlet 4" outlet 22" long 15* angle cut non rolled tip.
http://store.summitracing.com/largei...pe-12640_w.jpg
That will be going in the location of the stock resonator.
http://store.summitracing.com/largei...pe-35109_w.jpg
And that will obviously be my tip and the end of the piping.
So cliff notes. CIA header dp w/ cat, magnaflow 2.5" inlet outlet with a 6"x27" case with a 33" over all length resonator/muffler, magnaflow 2.5"inlet 4" outlet 22" long 15* angle cut non rolled tip.
Thread Starter
Joined: 05-04-08
Posts: 36,934
Likes: 2
From: The 405
one of each. i'm getting a full custom catback made at the local shop and i'm putting that muffler/resonator on the part of the exhaust thats right after the dp (where the stock resonator is). the part that is straight down the middle of the car. then i'll be putting the tip on after the pipe goes over the rear "axle"
Thread Starter
Joined: 05-04-08
Posts: 36,934
Likes: 2
From: The 405
its already got a straight through muffler on there. but i want more. and it was a shity job on it anyway.
bumpers
bumpers
Last edited by EXsoccer1921; Dec 4, 2008 at 05:29 PM. Reason: Automerged Doublepost
hahaha
Senior Member
Joined: 07-29-05
Posts: 7,915
Likes: 0
From: AZ
Its gonna be badass. Going to be getting the CIA header/dp with cat, and then a custom 2.5" cat back which will consist of these two bad boys.
http://store.summitracing.com/largei...pe-12640_w.jpg
That will be going in the location of the stock resonator.
http://store.summitracing.com/largei...pe-35109_w.jpg
And that will obviously be my tip and the end of the piping.
So cliff notes. CIA header dp w/ cat, magnaflow 2.5" inlet outlet with a 6"x27" case with a 33" over all length resonator/muffler, magnaflow 2.5"inlet 4" outlet 22" long 15* angle cut non rolled tip.
http://store.summitracing.com/largei...pe-12640_w.jpg
That will be going in the location of the stock resonator.
http://store.summitracing.com/largei...pe-35109_w.jpg
And that will obviously be my tip and the end of the piping.
So cliff notes. CIA header dp w/ cat, magnaflow 2.5" inlet outlet with a 6"x27" case with a 33" over all length resonator/muffler, magnaflow 2.5"inlet 4" outlet 22" long 15* angle cut non rolled tip.
Thread Starter
Joined: 05-04-08
Posts: 36,934
Likes: 2
From: The 405
CIA 4-1 and dp w/ a cat. but that will be going on a while after the exhaust
Last edited by EXsoccer1921; Dec 5, 2008 at 12:57 AM. Reason: Automerged Doublepost
Thread
Thread Starter
Forum
Replies
Last Post