Cobalt SS Network
Cavi on top, Cobalt on bottom
Cavi on top, Cobalt on bottom
0 2019/01/18 05:17:35
0 2019/02/12 06:37:56
0 2019/03/04 07:44:56
0 2019/03/04 07:45:56
0 2019/03/04 07:45:59
0 2019/02/07 06:00:34
0 2019/03/04 07:46:12
0 2019/02/07 06:01:17
Ex BMW wire schematic
Ex BMW wire schematic
0 2019/03/05 05:59:13
LS example accelerator pedal and throttle body. LSJ TB is different in that it has 2 additional pins for an additional +5V power and ground.
LS example accelerator pedal and throttle body. LSJ TB is different in that it has 2 additional pins for an additional +5V power and ground.
0 2019/03/05 05:59:15
Pinout sensor ground
Pinout sensor ground
0 2019/03/05 05:59:16
Pinout sensor power
Pinout sensor power
0 2019/03/05 05:59:17
0 2019/03/06 09:56:11
Molex 63811-1000
Molex 63811-1000
0 2019/03/06 10:00:22
0 2019/03/06 10:04:24
Deustch pin-socket terminals
Deustch pin-socket terminals
0 2019/03/06 10:05:06
It's slow tedious work but I did make some progress on the harness between the AEM and firewall.
It's slow tedious work but I did make some progress on the harness between the AEM and firewall.
0 2019/03/06 18:32:47
0 2019/03/10 06:08:21
0 2019/03/10 06:08:51
0 2019/03/10 06:09:11
0 2019/03/10 06:11:56
0 2019/03/10 17:36:50
0 2019/03/10 17:37:13
0 2019/03/10 17:37:30
0 2019/03/10 17:37:52
0 2019/03/12 18:17:14
0 2019/03/14 05:23:49
0 2019/03/18 05:36:46
0 2019/03/18 05:36:58
0 2019/03/18 05:37:10
Electrical connector clip broke so I had to implement another "zip-tie mod"
Electrical connector clip broke so I had to implement another "zip-tie mod"
0 2019/03/18 05:37:22
Male bottom end was slightly to large in diameter to work with anything on stock system. Only part I didn't end up using out of the kit.
Male bottom end was slightly to large in diameter to work with anything on stock system. Only part I didn't end up using out of the kit.
0 2019/03/24 18:09:04
0 2019/03/24 18:13:07
0 2019/03/24 18:13:57
Ended up configuring the pressure regulator as shown. Used 2 ZZP provided fuel fittings and added my own 45 deg hose fitting for boost/vac signal. Drilled out the center hole larger to use fuel filter bolt to attach both.
Ended up configuring the pressure regulator as shown. Used 2 ZZP provided fuel fittings and added my own 45 deg hose fitting for boost/vac signal. Drilled out the center hole larger to use fuel filter bolt to attach both.
0 2019/03/24 18:14:39
One of the fittings in ZZP's Z-configuration would rotate. I don't know if that means leaking issues or not.
One of the fittings in ZZP's Z-configuration would rotate. I don't know if that means leaking issues or not.
0 2019/03/24 18:18:10
Ran 12 Ga. wire to power pump through relay that has ground reference trigger up front from the AEM. Power wire for AEM also ran.
Ran 12 Ga. wire to power pump through relay that has ground reference trigger up front from the AEM. Power wire for AEM also ran.
0 2019/03/24 18:20:22
Drilled a hole to run power wires to pump. Didn't have any grommets on hand so did it just like this and running the loom through. Packed inside of loom and all around hole with dielectric grease to seal it up. I de-burred the bore so I think I can get decent life out of this.
Drilled a hole to run power wires to pump. Didn't have any grommets on hand so did it just like this and running the loom through. Packed inside of loom and all around hole with dielectric grease to seal it up. I de-burred the bore so I think I can get decent life out of this.
0 2019/03/24 18:22:08
0 2019/03/24 18:25:36
You can see the underside wire routing here
You can see the underside wire routing here
0 2019/03/24 18:26:52