Stock Muffler Replacement
Stock Muffler Replacement
* New Video added at bottom of original post*
Installed my ZZP catless DP over the weekend (**** YOU top resonator bolt and your rusty, grimey ass self). Excited, I started her up and was quickly reminded of the first go-round (RY sedan, MPX catless) and how it just wasn't aggressive enough for my taste. Prior to selling my RY sedan, I had plans to install a Dynomax bullet in place of the stock muffler to try and add a little more agressive tone but obviously didn't get around to it.
Well, yesterday I was doing my research for what I was after (case length,resonator/muffler, stainless/aluminum, etc.) and stumbled upon a great deal for a stainless steel "muffler" (more of a resonator than anything) from Pypes called an M-80.
Plan on keeping the factory resonator to create my own "FL" exhaust
I also plan to re-use the factory tip too.
Details:
14" case length (actual muffling piece)
4" diameter case
2 1/2" in/out, center/center
perfourated chamber with heat resistant packing (similar to a glass pack without the fiberglass and protruding louvers)
* New Video added*
Installed my ZZP catless DP over the weekend (**** YOU top resonator bolt and your rusty, grimey ass self). Excited, I started her up and was quickly reminded of the first go-round (RY sedan, MPX catless) and how it just wasn't aggressive enough for my taste. Prior to selling my RY sedan, I had plans to install a Dynomax bullet in place of the stock muffler to try and add a little more agressive tone but obviously didn't get around to it.
Well, yesterday I was doing my research for what I was after (case length,resonator/muffler, stainless/aluminum, etc.) and stumbled upon a great deal for a stainless steel "muffler" (more of a resonator than anything) from Pypes called an M-80.
Plan on keeping the factory resonator to create my own "FL" exhaust
I also plan to re-use the factory tip too.
Details:
14" case length (actual muffling piece)
4" diameter case
2 1/2" in/out, center/center
perfourated chamber with heat resistant packing (similar to a glass pack without the fiberglass and protruding louvers)
* New Video added*
Last edited by T-Man; Feb 24, 2013 at 03:13 PM.
I'm after a semi-aggressive tone but something that's relatively clean.
You the man Jay!
I was not about to pay them prices again! Haha... Thanks man, I hope so.
$46 shipped to my door.
Between the turbo, stock resonator and this larger resonator it should sound great. It's nothing like an SS/SC
$46 shipped to my door.
Between the turbo, stock resonator and this larger resonator it should sound great. It's nothing like an SS/SC
Member
Joined: 08-22-08
Posts: 369
Likes: 0
From: Colorado
I have an 09. I went to my friendly muffler shop, had them cut everything off behind the cat, and had them custom bend a 3" pipe welded directly to the cat and routed to the stock location. I used a cheap, generic 3" ID glass pack, installed backwards (it's about 16" long - you can look up the pipe from the exhaust tip), mounted in the stock location, and then added a 3" tip. It sounds great, no back pressure to speak of, and looks absolutely legal to any law enforcement.
Didn't cost an arm and a leg. It was about $200 for everything.
Scott
Didn't cost an arm and a leg. It was about $200 for everything.
Scott
Senior Member
Joined: 09-14-12
Posts: 964
Likes: 1
From: Warner Robins
I have an 09. I went to my friendly muffler shop, had them cut everything off behind the cat, and had them custom bend a 3" pipe welded directly to the cat and routed to the stock location. I used a cheap, generic 3" ID glass pack, installed backwards (it's about 16" long - you can look up the pipe from the exhaust tip), mounted in the stock location, and then added a 3" tip. It sounds great, no back pressure to speak of, and looks absolutely legal to any law enforcement.
Didn't cost an arm and a leg. It was about $200 for everything.
Scott
Didn't cost an arm and a leg. It was about $200 for everything.
Scott
Installed my ZZP catless DP over the weekend (**** YOU top resonator bolt and your rusty, grimey ass self). Excited, I started her up and was quickly reminded of the first go-round (RY sedan, MPX catless) and how it just wasn't aggressive enough for my taste. Prior to selling my RY sedan, I had plans to install a Dynomax bullet in place of the stock muffler to try and add a little more agressive tone but obviously didn't get around to it.
Well, yesterday I was doing my research for what I was after (case length,resonator/muffler, stainless/aluminum, etc.) and stumbled upon a great deal for a stainless steel "muffler" (more of a resonator than anything) from Pypes called an M-80.
Plan on keeping the factory resonator to create my own "FL" exhaust
I also plan to re-use the factory tip too.
Will post video once I receive it and get it put on.
Details:
14" case length (actual muffling piece)
4" diameter case
2 1/2" in/out, center/center
perfourated chamber with heat resistant packing (similar to a glass pack without the fiberglass and protruding louvers)
Well, yesterday I was doing my research for what I was after (case length,resonator/muffler, stainless/aluminum, etc.) and stumbled upon a great deal for a stainless steel "muffler" (more of a resonator than anything) from Pypes called an M-80.
Plan on keeping the factory resonator to create my own "FL" exhaust
I also plan to re-use the factory tip too.
Will post video once I receive it and get it put on.
Details:
14" case length (actual muffling piece)
4" diameter case
2 1/2" in/out, center/center
perfourated chamber with heat resistant packing (similar to a glass pack without the fiberglass and protruding louvers)
I had a cordless one that was bad ass but after 5 years of abuse, she **** the bed. Definitely used antiseize when reinstalling them
Got the "muffler" installed today and it sounds awesome! No rasp, a nice deep tone and plenty of turbo whistle. Sounds exactly like the Turbo XS FL exhaust
Will post some pics and a video shortly.
Got the "muffler" installed today and it sounds awesome! No rasp, a nice deep tone and plenty of turbo whistle. Sounds exactly like the Turbo XS FL exhaust
Will post some pics and a video shortly.
Video added to original post, at the bottom.
Please be sure to skip to 1:12 on the video after the take off, unless you would like to watch a random car drive by lol
Please be sure to skip to 1:12 on the video after the take off, unless you would like to watch a random car drive by lol
Thanks JayI added a new video to the OP since the last one was **** (leaking at the v-band). Youtube compression really tones down the bass but it's still better than the previous video.
As you can tell, no rasp and no obnoxious fart can noise. Not a whole lot of change inside the car unless you roll the window(s) down.
Lets see if anyone notices the surprise in the video...
Thread
Thread Starter
Forum
Replies
Last Post
DANRICKARD
Problems/Service/Maintenance
8
Oct 1, 2015 12:08 AM
