carstedt

iTrader: (1)

do u have a mod list mr b? im curious as to wut u have

JSimons47

Come hangout with jsims & jbills

JSimons47

His set up changes everyday. He has like every aftermarket part. He's an aftermarket parts warehouse.

Slowbalt2000

iTrader: (1)

And youz a puzzy bitch

carstedt

iTrader: (1)

im just curious to wut he runs/ numbers and sum pictures!

JSimons47

I know he has Carrillo rods that I'd do dirty things for. & diamonds
Pretty sure he's putting stock rods back in his engine though.

The dude is a mad scientist with lsjs. Literally. It's impossible to get knowledge out of him unless you actually know him though.

carstedt

iTrader: (1)

any pictures of the car?

Melon

iTrader: (11)

Mr b. Do u have a good resource for porting and assembling a head?

carstedt

iTrader: (1)

im sure he does lol

JSimons47

I'll answer that for him.
Lsjion on here. Billabong on redline forums. Top notch LSJ guy with a lot of experience. He did johns head.

Melon

iTrader: (11)

Do they have a flow bench? Is lsjion even on here anymore?

Chevycobaltss3

iTrader: (2)

Carrillo rods are over rated. I mean over priced .. I have them and won't spend 950$ on them ever again lol.

JSimons47

He does not have a flow bench, no.
He isn't on here that frequently. I know him personally.

&& Carrillo Rods are probably the best rods for our car. & Carrillo is one of the top names throughout the automotive industry. Just trying to start more drama. GeeZ

Vander Nars

iTrader: (5)

Moral of the story ladies is if ur gonna make claims about someone have some proof to back it up or shut the **** up.

mrbelvedere

iTrader: (3)

the last setup that i ran on zzp dyno made 306 270 on 10.4 afr and 10 or 15 deg of wot timing at 6500 2.9 tvs boost was 20lbs and i was spinning to 8100 but ay 6500 the hg failed and it broke the block the deck wasent at the correct finish standard the shop wasent able to get it done that fine it was close but **** happens so i have now located a small shop that hass the tooling to finish the block to gm standards or a little finer they are just about done with the head and the deck finish looks great

and i dont have carrilo rods i have a set of the 300m crower rods that was used in the eco engines that crower built for gm

yes he is on this board pm me

carstedt

iTrader: (1)

oh god here we go again

-Rizzo-

damn that thing is so much nicer then the stock SC

JSimons47

Crower.. Sounds like Carrillo on the phone

mrbelvedere

iTrader: (3)

carrillo is ok crower is the best not to mention crower did 95% of the eco race engine r&d for gm and then they had a falling out so then eagle got all the data from gm and built cranks and rods and so fourth

JSimons47

I've always heard Carrillo is top notch stuff for all vehicles.

mrbelvedere

iTrader: (3)

carrilo is good stuff but crower is my opinion the best the k1 china rods look ok also i just swapped for a new set of them

JSimons47

& you prolly paid like $20 -______-

100% METH

iTrader: (3)

ordering mine tomorrow if paypal comes through

zrated89

iTrader: (15)

I have all the proof I need now will I waste my time to call his ass out no. He'll do that himself with the self exploding motors he continues to tune. There is proof scattered all over this forum as well in the various I blew my car threads and the. James name suddenly disappears from the op's signature so carry on

carstedt

iTrader: (1)

I still dont get how this is the tunes fault? Op have u gotten to look more into the engine yet?