2.2L LAP Performance Tech 2.2L LAP Performance Tech (2009+) 155 hp EcoTec with 150 lb-ft of torque

need help!!!

Old Feb 16, 2011 | 01:17 AM
  #1  
BlueBalt1113's Avatar
Thread Starter
Senior Member
iTrader: (2)
 
Joined: 08-09-09
Posts: 1,468
Likes: 0
From: Baltimore
need help!!!

so i am looking into going stage 2 comp cams with my 07 ls this spring but im not sure of what all to get to make this happen to where i wont destroy my motor someone or everyone please help!!!
Reply
Old Feb 16, 2011 | 01:34 AM
  #2  
redcobalt07's Avatar
Senior Member
iTrader: (18)
 
Joined: 12-06-09
Posts: 5,950
Likes: 0
From: Harrisburg, PA
They will not fit into your car. First off a 2007 is an L61 not a LAP. Second, the 2007+ years cannot take the aftermarket comp cams. They do not fit.
Reply
Old Feb 16, 2011 | 02:52 PM
  #3  
BlueBalt1113's Avatar
Thread Starter
Senior Member
iTrader: (2)
 
Joined: 08-09-09
Posts: 1,468
Likes: 0
From: Baltimore
um first off the 07 is a lap engine just saying so what should i do to get a power boost cause i want power lol
Reply
Old Feb 16, 2011 | 02:54 PM
  #4  
BlueBalt1113's Avatar
Thread Starter
Senior Member
iTrader: (2)
 
Joined: 08-09-09
Posts: 1,468
Likes: 0
From: Baltimore
i swore on it being a lap cause it does not look like the l61 with the coil pack on top from what ive seen
Reply
Old Feb 16, 2011 | 06:37 PM
  #5  
jbenso4's Avatar
Senior Member
iTrader: (1)
 
Joined: 08-18-07
Posts: 1,098
Likes: 0
From: Rochester NY
coil pack has nothing to do with it...2009+ are LAP, you have an L61, but anyways i had Comp stage 2 cams in my 2007. All it requires is a tune from trifecta
Reply
Old Feb 16, 2011 | 06:50 PM
  #6  
C_A_D88's Avatar
Senior Member
 
Joined: 12-05-10
Posts: 3,877
Likes: 3
From: newmarket
yea man mines an 07 it a l61 laps are 09 n up
Reply
Old Feb 16, 2011 | 07:58 PM
  #7  
redcobalt07's Avatar
Senior Member
iTrader: (18)
 
Joined: 12-06-09
Posts: 5,950
Likes: 0
From: Harrisburg, PA
Originally Posted by jbenso4
coil pack has nothing to do with it...2009+ are LAP, you have an L61, but anyways i had Comp stage 2 cams in my 2007. All it requires is a tune from trifecta
how did you get the cams to fit into your 2007?
Reply
Old Feb 17, 2011 | 11:44 AM
  #8  
jbenso4's Avatar
Senior Member
iTrader: (1)
 
Joined: 08-18-07
Posts: 1,098
Likes: 0
From: Rochester NY
they were made for it. only difference is when i had them, i needed to get the cam positioning sensor pressed on. Now Vince has the capability to tune it so that is not necessary. Just make sure if you do it you get the springs and retainers too.
Reply
Old Feb 17, 2011 | 03:17 PM
  #9  
BlueBalt1113's Avatar
Thread Starter
Senior Member
iTrader: (2)
 
Joined: 08-09-09
Posts: 1,468
Likes: 0
From: Baltimore
how much did it cost for you to do this and what was the power gain???
Reply
Old Feb 17, 2011 | 03:21 PM
  #10  
redcobalt07's Avatar
Senior Member
iTrader: (18)
 
Joined: 12-06-09
Posts: 5,950
Likes: 0
From: Harrisburg, PA
Still think you have a LAP?
Reply
Old Feb 17, 2011 | 03:23 PM
  #11  
BlueBalt1113's Avatar
Thread Starter
Senior Member
iTrader: (2)
 
Joined: 08-09-09
Posts: 1,468
Likes: 0
From: Baltimore
idk cause i look at pics of the l61 and to me it looks different but i guess it is
Reply
Old Feb 17, 2011 | 03:28 PM
  #12  
redcobalt07's Avatar
Senior Member
iTrader: (18)
 
Joined: 12-06-09
Posts: 5,950
Likes: 0
From: Harrisburg, PA
well the 2005 2006 L61's look different from the 2007 2008 L61's
Reply
Old Feb 17, 2011 | 03:31 PM
  #13  
reaper89's Avatar
Senior Member
iTrader: (2)
 
Joined: 11-22-07
Posts: 2,009
Likes: 1
From: Salem, WI
only because of how the coil packs are set up. 05-07 have a single pack for all 4 plugs, where as 07+ has 1 for each plug
Reply
Old Feb 17, 2011 | 05:33 PM
  #14  
BlueBalt1113's Avatar
Thread Starter
Senior Member
iTrader: (2)
 
Joined: 08-09-09
Posts: 1,468
Likes: 0
From: Baltimore
O ok but back to the cams
Reply
Old Feb 17, 2011 | 06:34 PM
  #15  
redcobalt07's Avatar
Senior Member
iTrader: (18)
 
Joined: 12-06-09
Posts: 5,950
Likes: 0
From: Harrisburg, PA
You aren't going to find a set of cams from any company. Your best best is getting a set custom grinded from a machine shop.
Reply


Thread Tools
Search this Thread

All times are GMT -4. The time now is 05:26 PM.