Mark this thread as Unsold
FS: 60 lbs, 2.7 w/ Hub, Pulley Tensioner
06-24-2008, 01:46 AM
#1
Senior Member
Thread Starter
Join Date: 03-09-06
Location: "The Valley"-California
Posts: 2,425
Likes: 0
Received 0 Likes
on
0 Posts
FS: 60 lbs, 2.7 w/ Hub, Pulley Tensioner
FS:
60lbs Siemens Deka Flow Matched Injectors 11k (no harness): $180 shipped obo (SOLD MoneyPit)
2.7 ZZP pulley with Hub: $50 shipped obo (Sold MoneyPit)
ZZP Adjustable Pulley Tensioner: $80 shipped obo
$300 for everything
Also have stock SS Recaro's $550 oboLocal Pick Up Only
Will accept trades, I'm looking for an exhaust or cosmetic stuff, let me know what you got. Thanks all!!!
60lbs Siemens Deka Flow Matched Injectors 11k (no harness): $180 shipped obo (SOLD MoneyPit)
2.7 ZZP pulley with Hub: $50 shipped obo (Sold MoneyPit)
ZZP Adjustable Pulley Tensioner: $80 shipped obo
$300 for everything
Also have stock SS Recaro's $550 oboLocal Pick Up Only
Will accept trades, I'm looking for an exhaust or cosmetic stuff, let me know what you got. Thanks all!!!
Last edited by juststickit124; 06-26-2008 at 11:12 AM.
06-24-2008, 02:32 AM
#6
so if i got these, the harness, the gm stage2 belt. meth and a h/e. would i be all set except for a tune??
no other mods, but i am getting header downpipe and catback soon. 3" if i get these mods
no other mods, but i am getting header downpipe and catback soon. 3" if i get these mods
Last edited by EXsoccer1921; 06-24-2008 at 02:32 AM. Reason: Automerged Doublepost
06-24-2008, 02:36 AM
#7
Senior Member
Thread Starter
Join Date: 03-09-06
Location: "The Valley"-California
Posts: 2,425
Likes: 0
Received 0 Likes
on
0 Posts
I wouldn't run the meth without header and DP until you get it. but yes just a tune. I'm not even sure you need a stage 2 belt cause it's adjustable, check on that first though, i'm not 100% sure at all
08-15-2008, 12:45 PM
#13
Member
Join Date: 03-22-07
Location: Indianapolis, IN
Posts: 393
Likes: 0
Received 0 Likes
on
0 Posts
08-15-2008, 12:56 PM
#14
Banned
Join Date: 04-23-08
Location: USA
Posts: 138
Likes: 0
Received 0 Likes
on
0 Posts
Um, dude when you mean bigger I'm assuming that you mean like a smaller size pulley?? Like lower than a 2.8? If so then yes. Now if you're really meaning going larger like 3.0 which is backwards then no you don't
08-19-2008, 07:25 AM
#15
Member
Join Date: 03-22-07
Location: Indianapolis, IN
Posts: 393
Likes: 0
Received 0 Likes
on
0 Posts
ya i have a 3.1" pulley right now. lookin to put on my 2.9" pulley. my stock tensioner is shot so i was askin if i can use the adjustable for 2.9 or even 3.1.
08-19-2008, 08:32 AM
#16
Banned
Join Date: 04-23-08
Location: USA
Posts: 138
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post