Problems/Service/Maintenance Do you have problems with your new 2.0, 2.2, or 2.4L? What kind of service did you have done?

wierd issues, please help....

Thread Tools
 
Search this Thread
 
Old Sep 24, 2009 | 09:42 AM
  #1  
Chevycobaltss3's Avatar
Thread Starter
Banned
iTrader: (2)
 
Joined: 10-24-08
Posts: 12,836
Likes: 1
From: Vine Grove Kentucky
wierd issues, please help....

Alright i hit a animal about a month and a half ago. Well it mess some stuff up, i put a used engine in and some other stuff well i was trying to due the passkey yesterday and i turn the car on to the on posiotion and my boost gauge went all the wat to 20lbs and more My run/ crank relay clicks like a mother effer, i mean real bad/. I due not have the starter on because when i was hoiseting the enigne up with the crossmeber and tranny, some ho it hit something ebcause it broke, what i am tryin to figure out is would a dead battery cause this.


Right now i am debating to blow my car up please help lol

Last edited by Chevycobaltss3; Sep 24, 2009 at 10:07 AM.
Reply
Old Sep 24, 2009 | 10:29 AM
  #2  
Sh0nuff's Avatar
Senior Member
 
Joined: 08-09-07
Posts: 557
Likes: 1
From: EAST TX
I think a dead battery would cause all of your cluster / guages to go all the way up and slowly tick back down, atleast that is what it did to me.
Reply
Old Sep 24, 2009 | 10:38 AM
  #3  
Chevycobaltss3's Avatar
Thread Starter
Banned
iTrader: (2)
 
Joined: 10-24-08
Posts: 12,836
Likes: 1
From: Vine Grove Kentucky
Good that is what i am hoping, it seems like every day that i am putin the balt back together, somehting goes wrong, i forgot about pass key, then the started positive prong breaks off. so yeah sucks, but at least i know it is prob the battery, it is not fully charged i hope..

thanks bro
Reply
Old Sep 24, 2009 | 11:35 AM
  #4  
Sh0nuff's Avatar
Senior Member
 
Joined: 08-09-07
Posts: 557
Likes: 1
From: EAST TX
a fuse can also cause that.
Reply
Old Sep 24, 2009 | 11:38 AM
  #5  
phillips01's Avatar
New Member
 
Joined: 09-26-08
Posts: 183
Likes: 0
From: michigan
make sure that ALL the ground cables are tight and not loose
Reply
Old Sep 24, 2009 | 11:40 AM
  #6  
yel-low's Avatar
Senior Member
 
Joined: 12-16-05
Posts: 1,965
Likes: 0
From: hagerstown,md
yeah exspecially on the block but did you put any new modules in like a pcm or a bcm such
Reply
Old Sep 24, 2009 | 12:26 PM
  #7  
Chevycobaltss3's Avatar
Thread Starter
Banned
iTrader: (2)
 
Joined: 10-24-08
Posts: 12,836
Likes: 1
From: Vine Grove Kentucky
Noi just put in a engine, took the ecu out of the car so it wouldnt get (hurt) lol. There was a ground cable from the chassis and i did not know where it went to the block, so i found a bolt that had a neck out of it so i put it there lol, i wonder if it could be that...

thanks guys
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
taintedred07
2.0L LNF Performance Tech
32
May 28, 2022 03:47 AM
Tupp
Suspension
5
Sep 30, 2015 08:18 PM
yellow dragon
Problems/Service/Maintenance
0
Sep 28, 2015 09:49 PM
SlowSaturn
Drivetrain
0
Sep 28, 2015 11:03 AM




All times are GMT -4. The time now is 02:12 AM.