Now a victim of Injen CAI woes
#51
Senior Member
Join Date: 07-15-05
Location: Ontario, Canada
Posts: 7,639
Likes: 0
Received 0 Likes
on
0 Posts
yeah injen cai are a big pice. spend the money and get a FUJITA COLD AIR INTAKE. its comes in two pieces this way you have room to tweek it. dont get me wrong it was a pain in the a$$ to put in. its a two person job but no rubbing and it screams! o yeah you might want to get a hydro shield bag to go over the open filter because water can get to it from the hole above the left fog light and the other open hole in the wheel well. i checked it on a day after it rained just to make sure and the bottom was wet but the hydro shield put s stop to that.
#53
i dont know what is worse the fitment issues or that
injen really messed up my intake tube by welding the mass
air bracket 180 off so when the sensor went in backwards
but hong was nice to deal with as stated before
injen really messed up my intake tube by welding the mass
air bracket 180 off so when the sensor went in backwards
but hong was nice to deal with as stated before
#54
Senior Member
Join Date: 07-15-05
Location: Ontario, Canada
Posts: 7,639
Likes: 0
Received 0 Likes
on
0 Posts
#55
Senior Member
the fender liner is not buldging and the filer does not hit the bumper, i had the jbp intake b4 this and the injen is night and day
#56
I'm seeing that you guys are mostly having a rubbing issue. Mine's rubbing a little, but most ly (when I let off the throttle at all) the tube bangs vilantly against the frame and the hole in the fender. There has got to be a better way......... I'm so frustrated!!
BTW >> On top if my intake woes, the tip to my muffler fell off on the freeway last week. My DC Sports muffler!! WTF!! I'm almost ready to give up modding..............
BTW >> On top if my intake woes, the tip to my muffler fell off on the freeway last week. My DC Sports muffler!! WTF!! I'm almost ready to give up modding..............
#61
<--- Injen removed and replaced with just a K&N filter. I also received zero replies when i asked for help even when i offered to pay for replacement parts. Also my MAF went haywire after about 7 months. May or may not have been the Injen's fault though.
#62
Senior Member
Join Date: 02-24-06
Location: Fort Collins, CO
Posts: 1,142
Likes: 0
Received 0 Likes
on
0 Posts
Injen
I no longer recommend this company to anyone
#65
New Member
Join Date: 02-08-07
Location: greensburg, pa
Posts: 126
Likes: 0
Received 0 Likes
on
0 Posts
If you don't take off u're hood strut, it pushes down on the intake when u close the hood. That is probably what caused it. If you notice, the tube sits higher than the stock airbox. Which causes closure problems. Your warranty is still good, so you'll probably get your $ back or a new intake. If you do get a new intake, take off the strut. I didn't notice that my hood was bowing out on that side until I got my carbon fiber piece. Surely enough, that was the problem. Give it a shot.
#66
Senior Member
Join Date: 11-07-06
Location: Nowheresville
Posts: 2,077
Likes: 0
Received 0 Likes
on
0 Posts
When I had issues like this with an intake on a older car of mine, I put a rubber tube connector over the section of pipe that was rubbing fixed the problem like a charm! I'll have to see if i have any pics!
#69
Senior Member
Join Date: 07-14-05
Location: Mesa, AZ
Posts: 795
Likes: 0
Received 0 Likes
on
0 Posts
I SENT THIS ONCE BEFORE... I THOUGHT YOU WERE A REPUTABLE COMPANY, I SEE OTHER MEMBERS ON THE COBALTSS.NET SIGHT ARE ALSO NOT GETTING A RESPONSE...NOT GOOD CUSTOMER RELATIONS... YOUR COMPANY IS SUCCESSFUL DON'T LET YOUR REPUTATION BE RUINED BY A DISGRUNTLED GROUP OF CAR OWNERS, UNLESS YOU DON"T GIVE A CRAP ABOUT OUR LITTLE GROUP ( IT'S BEEN A WEEK AND I'VE YET TO GET A RESPONSE, OTHERS HAVE WAITED LONGER) Big NO-NO in the CUSTOMER SERVICE INDUSTRY!
>From: "D_backer1@hotmail.com (Sam Hifler)" <d_backer1@hotmail.com>
>To: <tech@injen.com>
>CC: <d_backer1@hotmail.com>
>Subject: Injen intake for Cobalt ss/sc
>Date: Mon, 26 Mar 2007 17:23:14 -0700
>
>I purchased an intake through Intense Motorsports approx. 8 months ago...Installed as directed but there seems to fittiment issues with the product below are some pictures of the damage done to the intake due to it not fitting correctly. Now I am a member on the Cobaltss.net forums and I noticed that I am not the only one who has experinced this problem heres the link to a thread about said problem https://www.cobaltss.net/forums/show...t=injen+intake his intake is worn in the same manner as mine! What can be done to resolve this problem, one member had to put a $50 deposit to have his replaced but I don't feel that is fair when you already have the money for the one that is damaged. Please contact me at d_backer1@hotmail.com so this issue can be resolved. Thank you!
#70
Senior Member
Join Date: 02-24-06
Location: Fort Collins, CO
Posts: 1,142
Likes: 0
Received 0 Likes
on
0 Posts
your first inquery was similar to mine.... no response and it's been nearly a month. not gonna happen.
K&N on the other hand has been very responsive and helping me out with a whole different issue regarding their pipes.
K&N on the other hand has been very responsive and helping me out with a whole different issue regarding their pipes.
Thread
Thread Starter
Forum
Replies
Last Post