tvs dyno results
Thread Starter
Senior Member
Joined: 05-18-08
Posts: 2,495
Likes: 0
From: louisville k.y
tvs dyno results
I dont have the sheeys yet because i left the car their for clutch install and axle in stall.
It put down 290 whp the tq was low at only 250 lbs wich is due to the full 3" exhaust and no cat. ill have the sheet in a few days and it was on a mustang dyno wich i hear reads low so i dont know.i thought it would do better.
It put down 290 whp the tq was low at only 250 lbs wich is due to the full 3" exhaust and no cat. ill have the sheet in a few days and it was on a mustang dyno wich i hear reads low so i dont know.i thought it would do better.
Rent me! per hour
Joined: 03-22-07
Posts: 24,161
Likes: 20
From: Still fixing others mistakes.
I dont have the sheeys yet because i left the car their for clutch install and axle in stall.
It put down 290 whp the tq was low at only 250 lbs wich is due to the full 3" exhaust and no cat. ill have the sheet in a few days and it was on a mustang dyno wich i hear reads low so i dont know.i thought it would do better.
It put down 290 whp the tq was low at only 250 lbs wich is due to the full 3" exhaust and no cat. ill have the sheet in a few days and it was on a mustang dyno wich i hear reads low so i dont know.i thought it would do better.
Senior Member
Joined: 05-02-06
Posts: 1,848
Likes: 0
From: Auburn Hills, MI
Senior Member
Joined: 05-02-06
Posts: 1,848
Likes: 0
From: Auburn Hills, MI
no idea what kind of dyno be honest....multiple claims of people using a mustang dyno then going there(right when he opened this shop) to compare numbers...they say it was slightly inflated but only about 5hp difference...how true this is, i don't know
60's 2.5 exhaust cti h/dp stock pully
60's 2.5 exhaust cti h/dp stock pully
Senior Member
Joined: 06-03-07
Posts: 1,265
Likes: 0
From: Pittsburgh PA
I dont have the sheeys yet because i left the car their for clutch install and axle in stall.
It put down 290 whp the tq was low at only 250 lbs wich is due to the full 3" exhaust and no cat. ill have the sheet in a few days and it was on a mustang dyno wich i hear reads low so i dont know.i thought it would do better.
It put down 290 whp the tq was low at only 250 lbs wich is due to the full 3" exhaust and no cat. ill have the sheet in a few days and it was on a mustang dyno wich i hear reads low so i dont know.i thought it would do better.
Senior Member
Joined: 05-02-06
Posts: 1,848
Likes: 0
From: Auburn Hills, MI
wow, i thought i threw away my dyno sheet(this is from back in like oct) and i just found it looking for something else...
i was off with my numbers i apologize...it was 293.5hp with 274.8ft/lbs
and i don't see a dyno name or anything on here
i was off with my numbers i apologize...it was 293.5hp with 274.8ft/lbs
and i don't see a dyno name or anything on here
Senior Member
Joined: 05-02-06
Posts: 1,848
Likes: 0
From: Auburn Hills, MI
ok looking at this sheet even more...i don't know if i can even trust these numbers, i never payed attention to it before, but the tq and hp curves don't even cross at the 5252 rev mark...
never noticed it...so ignore my numbers
but you should work on your tune anyway and be able to pull out some more esp. with your setup...
never noticed it...so ignore my numbers
but you should work on your tune anyway and be able to pull out some more esp. with your setup...
Senior Member
Joined: 05-02-06
Posts: 1,848
Likes: 0
From: Auburn Hills, MI
i wish i could help ya, but since i don't even know if my car is making power
i have no clue, im actually quite pissed right now because i found my dyno sheet and finding how inaccurate it is...
do you have hpt?
i have no clue, im actually quite pissed right now because i found my dyno sheet and finding how inaccurate it is...
do you have hpt?
Last edited by twzted; Jun 8, 2009 at 12:26 PM. Reason: Automerged Doublepost
Not bad, and pretty typical. Our last TVS customer dyno'd 295WHP, he had 60's, header, dual pass, HE, intake.
Thread Starter
Senior Member
Joined: 05-18-08
Posts: 2,495
Likes: 0
From: louisville k.y
i am going to buy the75 mm pulley, meth. And see what happens .
well i just ordered it from ott,the pulley.I will have to wait for meth.
well i just ordered it from ott,the pulley.I will have to wait for meth.
Last edited by scott allen; Jun 8, 2009 at 07:26 PM. Reason: Automerged Doublepost
Thread Starter
Senior Member
Joined: 05-18-08
Posts: 2,495
Likes: 0
From: louisville k.y
area thank you , i will pass that to the dyno guy,i just ordered the 75 mm pulley from ott i hope the pistons will hold up. I only got 20 lbs and that was at the shifting point,so id say 18 lbs is what is is making, so the smaller pulley should make it all come in sooner and will make about 20 to 21 lbs .again thanks area ,if you ever need anything please feel free to pm me ,thanks.