Mark this thread as Unsold
FS; non lsd tranny and clutch/flywheel
02-05-2008, 07:10 PM
#1
New Member
Thread Starter
Join Date: 03-25-07
Location: north port, fl
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
FS; non lsd tranny and clutch/flywheel
just replaced the non-lsd tranny in my 05 ss due to a bearing noise i started hearing a month ago, when i got the tranny off its was apparent the throwout bearing is toast, but already had a lsd tranny so it was replaced. also went ahead and replaced clutch with only 71k miles.. car is driven by my g/f so its never seen the track. can take extra pics if necessary and will ship or meet anyone in florida halfway for delivery on either or both parts. make resonable offers or possible trade of aftermarket parts.
02-05-2008, 08:20 PM
#4
New Member
Thread Starter
Join Date: 03-25-07
Location: north port, fl
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
ecotecon18s- far as i know its just the throw out. i can take it to a tranny shop and have it completely run through. i'll just tack the expense onto the best offer i receive. there isn't any play in the input shaft and its had royal purple put in it every 15k.
spaz- ways a little over 100 lbs according to the label i got with the new tranny, cost me 200 in shipping from crate engine. so you'd have to come with a better offer then that.
spaz- ways a little over 100 lbs according to the label i got with the new tranny, cost me 200 in shipping from crate engine. so you'd have to come with a better offer then that.
02-05-2008, 08:36 PM
#5
Senior Member
Join Date: 04-29-06
Location: Mulberry, Florida
Posts: 2,977
Likes: 0
Received 0 Likes
on
0 Posts
ecotecon18s- far as i know its just the throw out. i can take it to a tranny shop and have it completely run through. i'll just tack the expense onto the best offer i receive. there isn't any play in the input shaft and its had royal purple put in it every 15k.
spaz- ways a little over 100 lbs according to the label i got with the new tranny, cost me 200 in shipping from crate engine. so you'd have to come with a better offer then that.
spaz- ways a little over 100 lbs according to the label i got with the new tranny, cost me 200 in shipping from crate engine. so you'd have to come with a better offer then that.
02-12-2008, 05:14 PM
#9
New Member
Thread Starter
Join Date: 03-25-07
Location: north port, fl
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
input shaft is undamaged in appearance on outside and has no bearing play in it. just the throw out seems to be bad. i can take a vid of what the play is if you'd like and load it on utube or something
sunfirejoe, need more of address to quote you on shipping, but i'd at least like to get 500 plus shipping.
sunfirejoe, need more of address to quote you on shipping, but i'd at least like to get 500 plus shipping.
08-11-2008, 05:33 PM
#15
New Member
Thread Starter
Join Date: 03-25-07
Location: north port, fl
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
not w/o pulling it apart and checking everything, but shifted fine it just made too much noise when the clutch wasn't depressed, the t/o bearing is toast though, g/f road the clutch like a damn grandma as you can see in the pics. i'm not looking for alot i traded my balt in on a new one and just have this taking up space. And i couldn't begin to tell ya what it'd cost to ship to canada.
Thread
Thread Starter
Forum
Replies
Last Post
importkiller
Problems/Service/Maintenance
11
09-30-2015 07:18 PM