Bored myself.

Debating on buying a Aeroceptor Interceptor gauge on the OTTP group buy for my Regal.

 

i'm in misery... we were doing cadwelding today(its how we bond grounds together) and basically you set a charge, light with an igniter and it melts the charge into a mold which forms around your ground wire... well you have to clean the mold occasionally and I was showing one of the new guys how to do it and when he couldn't get a piece of debris out... he tries to blow it out, which was as gay as it sounds, lol... but anyway, all that happened was I got a ****-ton of gun power and copper debris in my eyes(even wearing safety glasses, pretty sure I scratched my cornea because I can barely keep my eye open, I flushed my eyes and got it all out, but the damage had been done

I thought I was getting laid off tomorrow and was HOPING I would... they just put in a 40 man call at the Ferry and I was wanting to get on that ****, about 2 years up there, i'd have made some cash... but I made it through probably to at least the end of January or so where i'm at... which sucks, I was ready to get away from it

can't wait until I top out where I can make them decisions myself, because this morning when that call went in, i'd have dragged up and went and made me about $35/hr

what is really sucks is they laid one of the 1st year guys off, who can't go to the Ferry, you have to be a 3rd year... It was going to work out perfect for me... but nope, they ruined that, lol... one of the bad things about doing a good job for a contractor, sometimes it can really bite you in the ass, lol

 

Well I hope you filled out an accident report in case you have to file workmans comp?

 

no Paul, I don't suffer from pussyidis, lol... but seriously, its not too bad, i've had this happen before... if I wasn't certain all of it was out, I would, but your cornea heals fast, when I wake up in the morning it'll be healed... and have a nice layer of that eye **** over it... lol

 

You wouldn't think that if you impaired your vision permanently and didn't have documentation that it happened on the job.

They would basically tell you your SOL.

 

How much is it? And holy crap what a power increase. That boost gauge hit 25-27 in 3rd 4th :5th gear lol

 

It's a group buy son

 

Well how much is it gonna cost in a group buy lol

 

It all depends everyone is always diff. Most the time the more the people the less it is

 

Where's the link. That's the same gauge I was gonna buy.

 

https://www.cobaltss.net/forums/supp...up-buy-259761/

 

Awesome. That's the same one I've been wanting to get.

 

Well their u go

 

Yep. Just waiting on price now lol.

 

Should be like $217/shipped if you use USPS priority mail.

All you have to do is go to their site, select the one you want and put in the discount code listed in the thread

 

Well their u go

 

I will be doing a Track masters dyno Saturday. And then next week will be doing a Speed South dyno next weds. This way will all see the difference between them both.

 

That sounds like a good idea

 

i sent vince the new logs for today and i have my car PARKED til the problem fixed.... damn my luck.... But vince is the best at fixing problems lol... DTC PO106 on the car right now

 

MAP sensor, you sure you installed the 3 bar wiring correct?

I guess its possible you might have bought a bad 3 bar also.

 

i wired it the way it said. and yea it mite be a bad one. which the kit has two sensors i installed and i guess i'll wait to see what vince says and go from there. which if its a bad sensor i'll take the part# for it and go buy a new one this time.

 

Well according to the code it almost sounds like a short in the wiring or bad connection?

 

i'll go check the wiring out here in a bit after the motor cools. is it gonna be the one on the manifold or lower charge pipe?

 

No idea on which one, I would check both.

I do know the one on the lower IC pipe has problems with the wiring rubbing the ac compressor.

 

i think i'll bet my money on that one lol