Mine will look like that soon

 

Good stuff My other one will look like that soon too, then they will look opposite of how they did, playing motor musical chairs and ****

 

u pull it out the top???

i had Steve's out in about 4-5 hrs out the bottom. he was fitting the rings while i was pulling.

 

Redlines have a lot more engine bay room. After all electrical plugs were disconnected I hooked up the cherry picker and un-did the mount bolts and literally 5 minutes later it was out. Cranked the load leveler to drop the trans side down a bit and it squeaked right out trans and all. I planned to get it all ready then go to eat that evening at 6 then come back and take it out, but by 4 we had it on the ground next to the car lol.

In a few weeks I'll have round 2 with my 05. That one will take a little bit longer, but still shouldn't be too bad.

 

**** is not easy lemme tell u. Lol. Got the sc mounted and waiting to go get a dremel to cut so I can fit belt on. Bout to hooke up TB/spacer then move onto meth kit. Will try and upload a link to pic

 

And before anyone can say anything yes I know its dirty and will clean it up a bit after install. But heres some eye candy

http://s1241.photobucket.com/user/me...tml?sort=3&o=0

 

Holy sheet melon it's about time you did this haha. And no need to dremel. Need a smaller pulley

 

That thing looks fresh in that stock engine bay! lol shiny

 

Lol I'm already down to a 3.2 and having a 3.0 Powdercoated that will go on when the head does. Dunno that I will finish today. Trying to but think its gonna take another night/day to do meth kit. At O'Reilly's waiting on parts now

 

so 100%meths build went well until we went to put the rods on the pistons. the wrist pins are a Lil to tight for my liking so the engine will be finished in 2 weeks.
the problem is the small end of the rods were not set properly from the manufactur. the wrist pins go in but r to tight. if we wouldn't had ran into that issue the entire build would have take less than 24 hours and that with breaks and going out to eat.
i take blame for this cuz i trusted Wat i was told by the manufactur. all brand new parts so it should have worked.
made some calls today. they shouldn't have been tight so the rods will get the small ends honed for proper clearance.
we stuck the new block and crank Back in the car so it wasn't a total loss weekend.
Wen i go back down we will drop the pistons in and stick the head on and time it all up while its in the car.
then vroom vroom. lol

 

Sweet! Unfortunately I'm not gonna make it up to c u guys tonight. Wanted tp come get it tuned but haven't even run the meth kit yet

 

I have pulled it out the top and then this last time reinstalled from the top. I did the same thing Infra did, had a load leveler and tilted the hell out of it.

It might just be easier on the Redline.

 

quit using the word lil you sound like a wanna be unicorn thug

 

Well I got to drive my Dads brand new Audi S4 while I was home today. I think Im in love.

 

Srry i didn't know this was English class. Lmao. JK MrB

 

lol

 

This has TVS also?

 

Sc is bolted on. Almost ready to fire it up. Just gotta let laptop battery charge a bit to flash the scaler for ls4 and then its go time

 

Yup. 1320 even

 

Nice, I wasn't sure if they still used the tvs or not

 

Yep, Couldnt really hear the whine. However it was really quick and just an awesome car.

 

Just because we can't let this thread go a whole week without a post...

 

I know! Usually its popping

 

Installing a clutch in my friends car the next few nights, then the TVS will go to its new home.

 

Tvs still in my trunk. Not the most functional place for it