Crossing my finger it doesn't lol and if I'm done with the Polish I'll just was it again and it should be good to go

 

Hoping tomorrow or Wednesday. I'm going here: RG PICK-A-PART

 

nice a decent amount of cobalts.... also holy **** that yard is huge. Id be down to go theres only 1 part that id potentially need but for a dollar and gas thats not to bad to give it a shot. wed i work 3-12 though

 

What part would that be? I have an interesting schedule this week. What's a better day for you?

 

hood strut. its all the same to be honest. for the next 2 weeks im 3-12 m-f

 

Damn fair enough. I'm always off on Sundays but they close pretty early those days. I don't leave church in LC until like 1:45 or 2:00. Maybe something will work out.

 

You dont leave church until 2? You must have a pretty late service. I leave a little after 11.

 

I go to two services. 10a and 11:45a, but I'm running the camera too and I have to wait for my nephew and take him home. He does worship for the youthin their building.

 

Aah I forgot to get the hood strut lol

 

lol its all good. i have one but it doesnt compress so whenever i need to be under the hood i just pop it on and off. not a huge deal but if i can get a working on that would be better. and im not totally sure if the one i have is even broken or it just wont work with the carbon hood

 

In the process of installing my K04R

 

Nice man good luck I hope you enjoy the turbo

Mine holds but if wind picks up it will close the hood on me so I know I need a new one. I've been on the yunkyard so many times never remembered I need one lol

 

ya i forgot about that i remember we were going to try the one i have on yours to see if it works or not but forgot

 

Been working on these side markers. I got the resistors in and left them hooked to my battery directly for 1-1.5hrs and they work like a charm. I just need more E-6000 to finish them off.

 

Nice man can't wait to see them

 

nice i use e6000 for alot of things too

 

Removed my rack spacers, and volla, have a perfectly straight steering wheel again. If anyone has a crooked steering wheel, check your rack alignment before assuming you need an actual suspension alignment. I def drank the coolaid thinking I needed rack spacers. Sure the theory makes sense why you need them, but unless you are on coil overs or super low, you really shouldn't be experiencing bump steer. PA has the perfect roads to test bump steer to, lol.

 

I have them on but really haven't felt any difference

 

Nah, they really don't do much for a drop like on your car or my car.

 

My wheel has been crooked since i installed my rack spacers! Also got a bit of a pull where i need to usually hold my wheel to the right. Buut my whole subframe was out all winter so i think thats related. Haha

 

It's so nice have the wheel straight and spot on. Almost feels weird... I got so used to driving with the wheel crooked.

 

My wheel is slightly crooked, but the subframe was out as well. Not looking forward to getting my car on a rack

 

I pulled mine out when I had the subframe dropped weekend before last. No noticeable difference, given I'm on Powell YYZ v1 so not super low.

Adam did you lock the steering rack before dropping the subframe?

 

Yeah I put them in for the ottp springs but didn't take them out for the yyz lol but my steering wheel is straight with them so they will probably stay on

 

I'm not a fan of the washer style rack spacer OTTP uses now. My old rack spacers from OTTP were a nice square block of aluminum, and didn't screw up my steering wheel alignment like these did. I should have kept those, but thought I would never lower my car again, haha. Oh well, not needed in my case anyways.